Subject	They don't fit. I went through 3 sets with them
Posted by	BlackholeZ on November 25, 2016 at 11:21 AM
	This message has been viewed 402 times.
In Reply To	Shims with old stock FUCA & new Whiteline bushings. (n/m) posted by xpwarrior on November 24, 2016 at 09:18 AM
Message	The stack heights are all wrong. I've been over it with one of their tech guys several times. One of the ends (I can't remember if it's chassis side or upright) is too narrow, and results in a ton of play. They told me it had been addressed, but it hadn't. I even had to refund a customer the cost and eat the labor on a set. Not pleased. -Dan VTC Solenoid Caps and install instructions. "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Front Upper Control Arm Options? - sak01 19:42:01 11/22/16 I like my UAS set... - Ted (92TT) 22:53:58 11/22/16 Re: I like my UAS set... - VinZmax 07:13:07 11/23/16 Yes there's a bearing on the axial portion... - Ted (92TT) 11:11:56 11/23/16 Good luck getting them. I tried getting the road/race - MixManMash 07:19:33 11/23/16 That sucks. Definitely worth the money if you want solids. (n/m) - Ted (92TT) 11:13:32 11/23/16 shim kit with new stock FUCA (n/m) - Bernie (NoVA) 01:22:59 11/23/16 2nd for your setup, this is the way to go (n/m) - WhiTTe Z 08:28:32 11/23/16 I 100% agree as well. - Goldchocobo 01:18:53 11/24/16 Shims with old stock FUCA & new Whiteline bushings. (n/m) - xpwarrior 09:18:02 11/24/16 Exactly what I want to do too. (n/m) - zquikone 12:26:12 11/24/16 Is there anything special regarding the Whiteline bushing - sak01 08:17:48 11/25/16 They were just much cheaper than buying new stock FUCAS. (n/m) - xpwarrior 19:53:28 11/25/16 The whiteline eccentric kit is a nice option if you want - black300zx 08:27:16 11/25/16 They don't fit. I went through 3 sets with them - BlackholeZ 11:21:48 11/25/16 The W51219 bushings? Mine fit fine and have - xpwarrior 19:55:05 11/25/16 Had to go back to my emails to check - BlackholeZ 00:56:29 11/29/16 False - the OEM bushings are better. (n/m) - Bernie (NoVA) 19:54:19 11/25/16 True - OEM may be better but Whiteline is still an option. (n/m) - xpwarrior 19:56:59 11/25/16 whitelines about about 160?$ its easier to just replace the - Dane (Houston) 10:51:38 11/28/16 Thanks for the insight. OEM arms it is. (n/m) - zquikone 11:47:08 11/29/16 I've tossed out 2 sets of old school Stillen slip box units - Bernie (NoVA) 20:15:09 12/02/16 ... - Bernie (NoVA) 20:20:59 12/02/16 Re: Front Upper Control Arm Options? - sak01 11:24:02 11/23/16 Yes, the long bolts need the extra space to insert. - jzack 13:56:02 11/23/16 You're being overly cautious. I move them all the time w. n - Bernie (NoVA) 19:01:33 11/23/16 No, you can unbolt the master w/ fluid lines attached and - Bernie (NoVA) 19:00:17 11/23/16 Re: No, you can unbolt the master w/ fluid lines attached and - sak01 21:59:04 11/23/16 Got them installed last night - sak01 09:07:40 11/26/16 Got the alignment done this morning - sak01 12:41:50 11/27/16 Enjoy (n/m) - Bernie (NoVA) 15:18:46 11/30/16 any pics available of the stock ones installed? - sak01 23:13:01 11/23/16 The side w. the L or R goes inboard. (n/m) - Bernie (NoVA) 19:57:30 11/25/16 KTS at RHD japan currently on sale - Dane (Houston) 17:23:12 11/23/16
Post a Followup	You cannot reply to this message because you are not logged in.