Subject	Someone did a pretty thorough teardown last winter
Posted by	BlackholeZ on February 03, 2016 at 11:04 PM
	This message has been viewed 418 times.
In Reply To	I'd like to see a comparison between the intake piping posted by not4resaleZ on February 03, 2016 at 09:31 AM
Message	and posted a ton of pics here. I was curious to compare the induction piping as well. Turbo inlets go forward and up from the inlet, but pretty straight, and pretty large. Turbo outlets point down and then turn forward just above the crossmember IIRC. I'm trying to dig up the guy's post but coming up dry. -Dan VTC Solenoid Caps and install instructions. "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	GTR - 300ZX plenum comparison - vorpalZ 10:33:29 02/01/16 Nice! If only the VG had heads like the VR... - The Hawk 10:39:43 02/01/16 Yep. I looked in the lower plenum at the cylinder heads of - MixManMash 11:02:24 02/01/16 how much more massive, proportionally speaking? - LJZTT 19:38:23 02/01/16 I didn't measure exactly. But port sizes on modern engines - MixManMash 20:51:23 02/01/16 Also has to do with variable valve timing (n/m) - ztunerz 20:51:48 02/02/16 For sure. VVT sure has changed from the days of VTC. (n/m) - MixManMash 10:10:04 02/03/16 I don't have specific #'s but...... - The Hawk 12:39:57 02/03/16 Isn't that kind of what I said? (n/m) - MixManMash 15:10:39 02/03/16 Yes and I was just elaborating.... - The Hawk 18:00:08 02/03/16 Thanks for posting...always curious about that (n/m) - Madhatter10-6 10:44:14 02/01/16 Very cool to see! - Polish 11:07:22 02/01/16 Are the holes the top/end of each runner for idle air? - cherry 12:12:50 02/01/16 good question.. or egr...pcv... (n/m) - LivinTheDream 15:04:05 02/03/16 Thanks for posting!! (n/m) - OverZealous (CT) 19:02:58 02/01/16 Re: GTR - 300ZX plenum comparison - induetime 10:04:14 02/02/16 Z32 plenum was designed for the NA and works fine for - not4resaleZ 14:02:39 02/02/16 Re: GTR - 300ZX plenum comparison - Bigwill837 14:11:35 02/02/16 The phone in your pocket has more computational power now - Dallas DamonZ 15:11:49 02/02/16 Correct. - MixManMash 16:14:23 02/02/16 GTR was designed with the latest supercomputer... - vorpalZ 16:21:52 02/02/16 Yes, but the Z32 was on a Cray-2, which reads Cray-Z. Lol. (n/m) - MixManMash 18:34:36 02/02/16 didnt GTM build and cast a lower intake manifold to run the - Dane (Houston) 19:38:53 02/02/16 That's pretty cool. - Dallas DamonZ 23:51:14 02/02/16 We would just need a mad scientist to make those throttle - Polish 00:19:26 02/03/16 Haltech Elite 2500 + OZMO dual TB controller = done. - 96300NAZ 12:32:30 02/03/16 ^While I will be following that path as well - -Grimm- 14:05:51 02/03/16 Go on... How would this work? - Polish 00:07:56 02/04/16 All you would need is a microcontroller and... - -Grimm- 10:18:56 02/04/16 What about some crazy rigging to use stock or modified - Polish 15:38:27 02/04/16 Everything is possible - -Grimm- 17:01:38 02/04/16 ^exactly. Main one being the tuning benefits. But... - 96300NAZ 21:37:55 02/04/16 On the SZ blog there is a turbo 370z with the GTR plenum (n/m) - puchy 07:17:12 02/03/16 quite cool (n/m) - Adam (NoVA) 07:42:06 02/03/16 They did. GTM is no longer in business though... - MixManMash 10:12:40 02/03/16 I'd stay well away from GTM/ Gamma... - vorpalZ 11:33:44 02/03/16 I'd like to see a comparison between the intake piping - not4resaleZ 09:31:34 02/03/16 Someone did a pretty thorough teardown last winter - BlackholeZ 23:04:10 02/03/16 found it: - BlackholeZ 23:09:36 02/03/16
Post a Followup	You cannot reply to this message because you are not logged in.