Subject	Re: Good Luck!
Posted by	acetrebo on August 31, 2025 at 9:32 PM
	This message has been viewed 5854 times.
In Reply To	Good Luck! (n/m) posted by Denis on August 29, 2025 at 04:43 PM
Message	Ugh. Replaced the master and slave, same problem. She's coming back apart in a few weeks. Clutch fork and pivot ball I guess, thats the only thing left I can try to replace to fix it. Same thing. Even with car off, if I put it in 1st, and push the clutch all the way to the floor, it doesn't release, I can't turn the wheel. Even off, if clutch is in I should be able to turn it but its locked in gear and wont turn. I guess I'll be a Z transmission expert soon lol. Getting LOTS of practice!
Follow Ups	Need clutch help - acetrebo 14:27:05 08/26/25 Re: Need clutch help - acetrebo 16:07:59 08/26/25 Re: Need clutch help - acetrebo 17:08:33 08/26/25 Re: Re: Need clutch help - itsa300zx 17:38:49 08/26/25 Re: Re: Re: Need clutch help - acetrebo 18:01:59 08/26/25 Re: Re: Re: Re: Need clutch help - acetrebo 22:23:31 08/26/25 Any updates for us on your clutch release issue? - itsa300zx 11:30:40 09/15/25 Likely installed clutch disc in backwards - However, check - Ghoztt (MD) 10:56:58 08/27/25 Agreed, I think it would be best to pull the trans again - Polishzx 16:46:35 08/27/25 Re: Agreed, I think it would be best to pull the trans again - acetrebo 23:58:01 08/27/25 The stock ones can flex but I don't think enough to not get - Polishzx 00:49:06 08/28/25 Re: The stock ones can flex but I don't think enough to not get - acetrebo 08:05:51 08/28/25 Re: Re: The stock ones can flex but I don't think enough to not get - acetrebo 08:16:33 08/28/25 Re: Likely installed clutch disc in backwards - However, check - acetrebo 23:54:21 08/27/25 Sadly, it can and has been done. - Ghoztt (MD) 14:08:08 08/28/25 Re: Sadly, it can and has been done. - acetrebo 18:34:37 08/28/25 Re: Likely installed clutch disc in backwards - However, check - acetrebo 00:00:07 08/28/25 Where are you in the "USA" ? One of the Z community - Denis 11:08:56 08/28/25 Re: Where are you in the "USA" ? One of the Z community - acetrebo 18:36:55 08/28/25 I may have my head on backward on this but - Denis 11:51:33 08/28/25 The bottoming out sounds like physical interference inside - Ghoztt (MD) 14:16:48 08/28/25 Re: The bottoming out sounds like physical interference inside - acetrebo 18:43:22 08/28/25 The bottoming out term I used - Denis 20:41:15 08/28/25 Re: The bottoming out term I used - acetrebo 22:22:06 08/28/25 Re: I may have my head on backward on this but - acetrebo 18:41:01 08/28/25 Re: Re: I may have my head on backward on this but - Denis 20:56:53 08/28/25 Re: Re: Re: I may have my head on backward on this but - acetrebo 22:13:40 08/28/25 OK, disregard my earlier suggestions - Denis 22:41:11 08/28/25 Re: OK, disregard my earlier suggestions - acetrebo 22:49:37 08/28/25 Re: OK, disregard my earlier suggestions - acetrebo 22:53:34 08/28/25 Sometimes it is possible to dig - Denis 13:21:13 08/29/25 Make that ding (n/m) - Denis 13:24:01 08/29/25 Re: Sometimes it is possible to dig - acetrebo 13:47:41 08/29/25 Good Luck! (n/m) - Denis 16:43:25 08/29/25 Re: Good Luck! - acetrebo 21:32:04 08/31/25 You most likely said, but did you replace the - Denis 23:59:07 08/31/25 Re: You most likely said, but did you replace the - acetrebo 08:18:16 09/02/25 Re: Need clutch help - mrchips 06:18:21 08/31/25 Re: Re: Need clutch help - acetrebo 08:21:28 09/02/25 clutch update - acetrebo 08:05:30 09/22/25 Re: clutch update - acetrebo 23:27:13 09/30/25 What exactly was the problem. Bent fork? TIA. (n/m) - mrchips 07:49:44 10/01/25
Post a Followup	You cannot reply to this message because you are not logged in.