Subject	Which is weird because my full 3" SZ setup didn't fit w/out
Posted by	PiotrC70 on November 26, 2019 at 10:28 AM
	This message has been viewed 215 times.
In Reply To	False... posted by ConVerTT on November 25, 2019 at 10:23 PM
Message	adding ~1/2" spacer. Tried a loose fit and tightening up as I go and that didn't work either. 1993 TT. R.I.P. 09.15.2010
Follow Ups	Regarding the rear crossmember that's just aft of the cats>> - Woodnutz 12:36:46 11/25/19 Re: Regarding the rear crossmember that's just aft of the cats>> - itsa300zx 13:08:03 11/25/19 False... - ConVerTT 22:23:43 11/25/19 JWT Genie also fits (n/m) - ConVerTT 22:29:21 11/25/19 Hmm, thats odd, even with my NA OEM pipes and Stillen - itsa300zx 09:56:51 11/26/19 That is strange for sure. I have a few combinations - ConVerTT 20:31:34 11/26/19 Which is weird because my full 3" SZ setup didn't fit w/out - PiotrC70 10:28:29 11/26/19 My SZ is 3-2.5 TPs with SZ 2.5 catback ... - ConVerTT 20:23:52 11/26/19 Fits ok with my SZ. I'd try clocking the mid-pipes slightly. (n/m) - Ted (92TT) 22:54:06 11/25/19 Thanks! This is going to be my approach to see what - Woodnutz 05:46:18 11/26/19 Mine worked fine on my 92 NA with LaBree cat back (n/m) - ctheobal 21:09:55 11/27/19 Pics? Maybe there is a rubber hanger longer than OEM? (n/m) - ZXoltan 13:58:27 11/25/19 I can maybe get a pic later tonight, but the cross-brace - Woodnutz 16:37:24 11/25/19 Re: I can maybe get a pic later tonight, but the cross-brace - itsa300zx 17:00:05 11/25/19 Yep, that’s it. I was concerned about it being structural, - Woodnutz 19:29:37 11/25/19 I think you've got a problem with your exhaust... - Barry (NJ) 15:52:29 11/25/19 That’s quite possible. I suspect I won’t get a whole lot, - Woodnutz 16:41:51 11/25/19 I've had to slice a small pie section out of some testpipes - Doug71zt(CAN) 21:47:28 11/25/19 No issues w/ 93 & Borla; or 96 & Magnaflow (n/m) - Gordo NA2LS Daytona 16:01:01 11/25/19 Don't crack your manifolds. (n/m) - spicyZ 21:55:44 11/25/19 Did it fit BEFORE you installed the TPs and DPs? - ConVerTT 22:37:20 11/25/19 Yes, it fit - previously untouched OEM install. Z1 TPs/DPs (n/m) - Woodnutz 05:38:02 11/26/19 hmmm strange. I dont have any combination with Z1 DPs - ConVerTT 20:34:35 11/26/19 You can add spacers to it and use longer bolts. (n/m) - Bernie (NoVA) 22:56:04 11/25/19
Post a Followup	You cannot reply to this message because you are not logged in.