Subject	Regarding the rear crossmember that's just aft of the cats>>
Posted by	Woodnutz on November 25, 2019 at 12:36 PM
	This message has been viewed 362 times.
Message	I didn't think too much of it when I installed my testpipes, but it's something I need to address. When I reassembled my exhaust with the downpipes and test pipes, Securing the rear cross-member pushed the whole exhaust upward to the point where it's not even hanging on the hangers. Also pushed the mufflers high enough that the tips are touching the rear bumper. I'm sure I can loosen the bolts to let things relax a little, but I don't think they'll drop much at all. Curious to see what y'all have done with this. Thanks!
Follow Ups	Regarding the rear crossmember that's just aft of the cats>> - Woodnutz 12:36:46 11/25/19 Re: Regarding the rear crossmember that's just aft of the cats>> - itsa300zx 13:08:03 11/25/19 False... - ConVerTT 22:23:43 11/25/19 JWT Genie also fits (n/m) - ConVerTT 22:29:21 11/25/19 Hmm, thats odd, even with my NA OEM pipes and Stillen - itsa300zx 09:56:51 11/26/19 That is strange for sure. I have a few combinations - ConVerTT 20:31:34 11/26/19 Which is weird because my full 3" SZ setup didn't fit w/out - PiotrC70 10:28:29 11/26/19 My SZ is 3-2.5 TPs with SZ 2.5 catback ... - ConVerTT 20:23:52 11/26/19 Fits ok with my SZ. I'd try clocking the mid-pipes slightly. (n/m) - Ted (92TT) 22:54:06 11/25/19 Thanks! This is going to be my approach to see what - Woodnutz 05:46:18 11/26/19 Mine worked fine on my 92 NA with LaBree cat back (n/m) - ctheobal 21:09:55 11/27/19 Pics? Maybe there is a rubber hanger longer than OEM? (n/m) - ZXoltan 13:58:27 11/25/19 I can maybe get a pic later tonight, but the cross-brace - Woodnutz 16:37:24 11/25/19 Re: I can maybe get a pic later tonight, but the cross-brace - itsa300zx 17:00:05 11/25/19 Yep, that’s it. I was concerned about it being structural, - Woodnutz 19:29:37 11/25/19 I think you've got a problem with your exhaust... - Barry (NJ) 15:52:29 11/25/19 That’s quite possible. I suspect I won’t get a whole lot, - Woodnutz 16:41:51 11/25/19 I've had to slice a small pie section out of some testpipes - Doug71zt(CAN) 21:47:28 11/25/19 No issues w/ 93 & Borla; or 96 & Magnaflow (n/m) - Gordo NA2LS Daytona 16:01:01 11/25/19 Don't crack your manifolds. (n/m) - spicyZ 21:55:44 11/25/19 Did it fit BEFORE you installed the TPs and DPs? - ConVerTT 22:37:20 11/25/19 Yes, it fit - previously untouched OEM install. Z1 TPs/DPs (n/m) - Woodnutz 05:38:02 11/26/19 hmmm strange. I dont have any combination with Z1 DPs - ConVerTT 20:34:35 11/26/19 You can add spacers to it and use longer bolts. (n/m) - Bernie (NoVA) 22:56:04 11/25/19
Post a Followup	You cannot reply to this message because you are not logged in.