Subject	If you have access to a competent machine shop and
Posted by	Tanley (ATL) on November 10, 2019 at 7:07 PM
	This message has been viewed 237 times.
In Reply To	Dang.. I was really hoping I wouldn't have to get a new cran posted by dTb on November 10, 2019 at 04:13 PM
Message	a good set of tools for verifying the tolerances and machine work. I'd say go for it. It you decide to go that route, have the machine shop agree in writing to fix any issues you may find prior to or during assembly and/or replace the block at their cost if they totally botch it. Verify all of their work and inspect the block prior to assembly. Also, there was a member renting out torque plates if you deem that necessary.
Follow Ups	Engine Teardown.. looking for input - dTb 17:34:45 11/09/19 This sounds like a nightmare. 5k, you should not be having - Tanley (ATL) 19:20:01 11/09/19 yes, compression test done before teardown was very low - dTb 01:47:45 11/10/19 I have been in contact with EPR (Mitch) throughout the build - dTb 02:29:23 11/10/19 Sorry you are going thru this. It's a shame the engine - SirpriZ 12:48:23 11/10/19 yeah return policies are pretty hard to catch on time.. - dTb 12:56:09 11/10/19 Well done. See my post above. (n/m) - SirpriZ 16:19:42 11/10/19 Re: Sorry you are going thru this. It's a shame the engine - Tech@EPR 15:31:56 11/14/19 You really think I'm going to bring the engine to - dTb 10:57:46 11/16/19 Re: yes, compression test done before teardown was very low - Tech@EPR 15:30:01 11/14/19 Thoughts - Cjw3 21:31:02 11/09/19 You seem to be hitting a few things on the head here... - dTb 02:14:41 11/10/19 No good if you catch the scratches on your Nail - Cjw3 07:30:00 11/10/19 If I need the crank re ground, do I just get thicker bearins - dTb 12:48:59 11/10/19 A couple of additional thoughts. I have found that some - SirpriZ 13:13:58 11/10/19 I don't think a chrome ring package was used.. I will check - dTb 15:56:50 11/10/19 Please follow up. I feel for you. You are handling yourself - SirpriZ 16:17:44 11/10/19 Oops, no phone number in profile. It is 818 425-4322. (n/m) - SirpriZ 16:22:30 11/10/19 Thank you for the offer.. I'll let you know how the - dTb 20:13:04 11/11/19 Grinding removes the Hard Facing. - Cjw3 14:02:30 11/10/19 Dang.. I was really hoping I wouldn't have to get a new cran - dTb 16:13:43 11/10/19 If you have access to a competent machine shop and - Tanley (ATL) 19:07:08 11/10/19 Ok thank you for that input.. I don't think the machine - dTb 20:16:39 11/11/19 I have access to metallurgical inspection equipment - megaDan 16:29:56 11/12/19 Yes we have....and i'm still working on part 2. LOL - itsa300zx 16:38:48 11/12/19 Reason I did this was because of EPR claims grinding upto... - itsa300zx 16:44:38 11/12/19 Re: Reason I did this was because of EPR claims grinding upto... - Tech@EPR 15:39:07 11/14/19 Sorry, I did miss read your post back then... - itsa300zx 12:58:26 11/15/19 I have another crankshaft as a sample if you like. (n/m) - MixManMash 07:59:33 11/13/19 Sure, another sample wouldn't hurt. (n/m) - itsa300zx 14:32:22 11/13/19 I have a spare crank. Not sure of it's condition.. and I'll - dTb 19:55:31 11/13/19 I'm assuming you are asking me? More data points would be - itsa300zx 12:23:41 11/14/19 Re: Thoughts - Tech@EPR 15:33:59 11/14/19 I have added pictures of both halfs of the bearings - dTb 11:37:11 11/16/19 From your Pics the Crank Journal is Tapered - Cjw3 11:00:07 11/17/19 ok, I can see how you would come to that conclusion - dTb 17:23:57 11/17/19 Plastigauge 101.. as I was taught.. - Cjw3 21:04:29 11/17/19 Re: Engine Teardown.. looking for input - Tech@EPR 15:27:52 11/14/19 Proof that you used your own sourced parts - dTb 11:18:18 11/16/19 Picture link inside - dTb 11:52:46 11/16/19 $8,500!? That is a serious chunk of change. (n/m) - Tanley (ATL) 12:17:55 11/16/19
Post a Followup	You cannot reply to this message because you are not logged in.