Subject	Jacked up the car this morning...
Posted by	thumper300zx on October 23, 2019 at 10:45 AM
	This message has been viewed 221 times.
In Reply To	Re: Re: My 90 NA did this.. posted by Cjw3 on October 23, 2019 at 07:19 AM
Message	Ran it until it got 'hot'. Turned on defrost, 90, full blast...took off cap and bleeder and ran it until I could see no bubbles and fluid was pouring out. Drove to work. Left at 90 in AUTO, and it stayed fan level 'ONE', defrost and floor the entire time. Immediately did diagnostics after stopping car. Showing 'WATER TEMPERATURE' of only 76. So, I'm assuming I've either got a plugged core or the valve isn't opening. Hoses going into heater core were ok, but lower than operating temp by 20-30 degrees. Perhaps indicative of no water flow. I plan on pulling the hoses from the back with car pointing slightly downhill (driveway slightly sloped) and flushing core to see if something isn't flowing. VISIT thumper300zx.com for PICS and TECH PAGES
Follow Ups	Heater doesn't work. Set to 90, AC is visibly operating... - thumper300zx 23:38:08 10/21/19 Oh, one more small detail... - thumper300zx 23:40:26 10/21/19 On this note, the A/C will turn off under hard acceleration - Agent X 06:42:23 10/22/19 Re: On this note, the A/C will turn off under hard acceleration - thumper300zx 18:39:13 10/22/19 Re: Re: On this note, the A/C will turn off under hard acceleration - thumper300zx 12:06:27 10/23/19 My 90 NA did this.. - Cjw3 07:16:23 10/22/19 ^^^ The blend motor (n/m) - ThisIsSparTTa 08:31:59 10/22/19 Re: My 90 NA did this.. - thumper300zx 18:37:38 10/22/19 Re: Re: My 90 NA did this.. - Cjw3 07:19:42 10/23/19 Jacked up the car this morning... - thumper300zx 10:45:07 10/23/19 The Blend Door Controls the Water Flow to the Core (n/m) - Cjw3 10:13:38 10/24/19 Re: The Blend Door Controls the Water Flow to the Core - thumper300zx 15:04:00 10/24/19 yes..BTDT (n/m) - Cjw3 18:39:20 10/24/19 Re: yes..BTDT - thumper300zx 19:56:11 10/24/19 I had some time today... - thumper300zx 14:54:36 10/26/19 PICS of what I did today... - thumper300zx 15:08:40 10/26/19 This looked hopeful, but it's for manual controls... - thumper300zx 16:17:39 10/26/19 Ran Diagnostics... - thumper300zx 21:50:57 10/22/19 Re: Ran Diagnostics... - mrchips 08:43:01 10/27/19 Re: Re: Ran Diagnostics... - thumper300zx 09:48:22 10/27/19 I'm gonna go back through diagnostics now that I know... - thumper300zx 12:24:00 10/27/19 Still not 100% sure I get the diagnostics...but - thumper300zx 23:00:06 10/27/19 Re: Still not 100% sure I get the diagnostics...but - thumper300zx 10:33:32 10/28/19
Post a Followup	You cannot reply to this message because you are not logged in.