Subject	Z32 cylinder 1 & 2 dead
Posted by	str86z on August 22, 2016 at 11:19 PM
	This message has been viewed 377 times.
Message	Hello all, looking for some help and I will try to.keep it simple. Used motor and auto tranny swap. Posted a while back about other issues which I have got sorted out now. My last major issue is that i am running on 4 cylinders. 1 and 2 have no change in idle when coil packs unplugged, all others are fine. I have tried: Switching coils and spark plugs from working cylinders. Pulling coil and plug and grounding them on plenum (good spark and shocked myself) Pulled plenum and spun CAS to verify fuel from injectors (all spraying with valve movement) Tried newer PTU Tried used ecu from crashed Z Compression test (all at 120 to 130, but these were with all the plugs still in engine, so wrong I know. But #'s consistent and other 4 working) So at this point I am lost, please help anybody.
Follow Ups	Z32 cylinder 1 & 2 dead - str86z 23:19:56 08/22/16 Re: Z32 cylinder 1 & 2 dead - Stokens (AR) 14:06:26 08/23/16 Re: Re: Z32 cylinder 1 & 2 dead - str86z 23:50:30 08/23/16 Re: Re: Z32 cylinder 1 & 2 dead - str86z 03:44:20 08/24/16 That is quite a bit of green stuff! - Stokens (AR) 16:42:32 08/24/16 you've done all the Easy Stuff.. Now lets hunt.. - Cjw3 20:18:21 08/23/16 Maybe try visual verifying that the PTU wiring color codes - jzack 21:37:54 08/23/16 Re: Maybe try visual verifying that the PTU wiring color codes - str86z 00:03:54 08/24/16 Re: you've done all the Easy Stuff.. Now lets hunt.. - str86z 23:57:55 08/23/16 Re: Re: you've done all the Easy Stuff.. Now lets hunt.. - str86z 04:13:23 08/24/16 i would look into the corrosion issue as posted above, - itsa300zx 08:28:40 08/24/16 I would solder the subharness into the main harness - -Grimm- 09:47:31 08/24/16 Re: I would solder the subharness into the main harness - str86z 19:29:58 08/24/16 Depends on your test conditions, but yes - -Grimm- 09:45:18 08/25/16 Re: Depends on your test conditions, but yes - str86z 01:15:58 08/26/16 How did you test the injectors? (n/m) - -Grimm- 13:36:23 08/26/16 Agreed. Starting to sound more like failing injectors. (n/m) - Stokens (AR) 17:24:39 08/26/16 Re: Agreed. Starting to sound more like failing injectors. - str86z 19:02:43 08/26/16 Videos of my tests on cyl. 1 & 2 - str86z 08:58:49 08/27/16 Re: Videos of my tests on cyl. 1 & 2 - str86z 13:30:36 08/28/16 Re: Videos of my tests on cyl. 1 & 2 - str86z 20:07:34 08/28/16 Hard to tell, maybe just the frame rate, but are they... - -Grimm- 13:48:58 08/29/16 Re: Hard to tell, maybe just the frame rate, but are they... - str86z 16:07:43 08/29/16 Start with checking the wire colors vs ECCS - -Grimm- 17:39:45 08/29/16 Re: Start with checking the wire colors vs ECCS - str86z 21:38:32 08/29/16 *VIDEO* Timing questions - str86z 21:44:33 08/31/16 Re: Videos of my tests on cyl. 1 & 2 - str86z 03:04:25 09/02/16 Suggestions I am so close - str86z 00:32:41 09/03/16 Re: Videos of my tests on cyl. 1 & 2 - str86z 04:19:57 09/06/16
Post a Followup	You cannot reply to this message because you are not logged in.