Subject	Re: Actually, the ECU *does* have o2 feedback at idle
Posted by	Dallas DamonZ on June 26, 2015 at 12:35 AM
	This message has been viewed 236 times.
In Reply To	Actually, the ECU *does* have o2 feedback at idle posted by zromtech on June 25, 2015 at 01:39 PM
Message	Interesting. Answers why Z-Lab hunts around at idle while waiting. I can sit there and watch the LM1 wideband get richer and richer then it cuts fuel, stalls and fights against itself then stabilizes and start getting richer again. Later When was the last time you *really* did something with your Z to call yourself a Z enthusiast? Member #1 PETZ
Follow Ups	What else to check... - Stanky 00:18:22 06/24/15 Don't feel offended, but let me ask you this.... - puchy 07:29:06 06/24/15 Compressed air to driver side, hockey puck blocking - Stanky 09:20:35 06/24/15 Check you idle stops. FSM section for TB setup. (n/m) - BoneZ (MD) 07:33:41 06/24/15 Will check tonight, thanks (n/m) - Stanky 09:22:17 06/24/15 EM-21 in the 95 FSM - BoneZ (MD) 19:19:40 06/24/15 Honestly i notice no change by disconnecting it - Stanky 19:34:00 06/24/15 Hell, that may be an issue. - BoneZ (MD) 19:49:52 06/24/15 if you changed smic piping you could mix up recirc and EBC - Dane (Houston) 09:53:50 06/24/15 I've been running the selin kit for a couple years now - Stanky 14:39:58 06/24/15 Re: I've been running the selin kit for a couple years now - Dane (Houston) 21:59:48 06/25/15 Have you tried it with just the TPS switch? (TPS sensor - ConVerTT 12:50:38 06/24/15 My NA is having this same issue. tried 2 TPS with clean pins - XTZ 18:09:08 06/24/15 So .... - ConVerTT 20:36:52 06/24/15 Can you run ECUtalk to check some parameters? (n/m) - OverZealous (CT) 17:45:25 06/24/15 Consult readings - Stanky 18:53:12 06/24/15 One more - Stanky 18:54:09 06/24/15 Re: One more - Dallas DamonZ 19:16:03 06/24/15 So... - ConVerTT 20:26:02 06/24/15 Correct! - Stanky 20:46:32 06/24/15 Awesome! - ConVerTT 23:20:02 06/24/15 Didn't realize it was open loop at idle - BlackholeZ 11:15:33 06/25/15 Actually, the ECU *does* have o2 feedback at idle - zromtech 13:39:07 06/25/15 Hmmm. That is interesting intel... - ConVerTT 16:44:11 06/25/15 Re: Hmmm. That is interesting intel... - zromtech 12:25:10 06/26/15 Should be able to disconnect the O2 and run at idle? (n/m) - BoneZ (MD) 12:29:51 06/26/15 yes, that should tell you if the O2s are involved (n/m) - zromtech 13:13:43 06/26/15 Ok great. Now how does this idle feedback interact - ConVerTT 09:03:08 06/27/15 Re: Ok great. Now how does this idle feedback interact - zromtech 10:31:23 06/27/15 Ok great. I was hoping that was the answer... - ConVerTT 11:43:47 06/27/15 Fuel pressure good, all injectors firing and ohm 12.5 - Stanky 14:22:44 06/27/15 Re: Actually, the ECU *does* have o2 feedback at idle - Dallas DamonZ 00:35:48 06/26/15 Mine would idle at mid 14 afr for about ten seconds - xpwarrior 10:43:27 06/26/15 Re: Mine would idle at mid 14 afr for about ten seconds - zromtech 13:01:56 06/26/15 FWIW, Nistune allows you to enable O2 feedback - aliaZ 17:24:47 06/26/15 You can also do that with Tunerpro or even hex editing - xpwarrior 18:22:31 06/26/15 or ZROM Pro!* - zromtech 11:39:28 06/27/15 Appreciate the static pics but was hoping for transients vid - OverZealous (CT) 18:13:29 06/26/15 Please let us know exactly what the problem turns out to be. (n/m) - Zuberman 01:28:00 06/25/15 I've had similar issues, it ended up being a bad MAF - Zvil (FL) 09:36:15 06/25/15 Good point ... - ConVerTT 10:52:55 06/25/15 I have suspected my MAF to be questionable for years. Maybe - Zuberman 12:24:25 06/25/15
Post a Followup	You cannot reply to this message because you are not logged in.