Subject	I think you have the rubber parts up-side down.
Posted by	Woody75 (Denver) on May 20, 2015 at 10:07 AM
	This message has been viewed 265 times.
In Reply To	Does this look right? posted by YlwPrlZTT on May 19, 2015 at 04:39 PM
Message	The washer section should be touching the head of the bolt, not the valve cover. But they should be squished more for sure as well. JackB nimble JackB quick JackB can suck my dick =P - james-lee 11/02/01 Arrogance is the #1 weapon against Supra Owners - MikeH 08/06/02 Dallas with a Z: I like the bulge dude 05/02/03 Bezbefootball: Does dick have anything for me? 10/21/03
Follow Ups	Does this look right? - YlwPrlZTT 16:39:10 05/19/15 also any tips on installing injectors? They are very - YlwPrlZTT 16:49:23 05/19/15 Put vasoline on the o-rings for the injectors - ZXRider 17:22:12 05/19/15 Pressing in is fine. Use longer screws to make it easier - jzack 20:07:24 05/19/15 I just snugged em "real good" with a screw driver. - Goldchocobo 17:34:03 05/19/15 ok, maybe i need to add half turn more just to be sure (n/m) - YlwPrlZTT 17:45:44 05/19/15 Good idea to check them a day or so later since the washers - jzack 20:09:20 05/19/15 I tightened them till they had a bit of a squat to them - BlackholeZ 21:01:21 05/19/15 This^^^ Mine were compressed. Looked like washers. No leaks. (n/m) - Zuberman 23:10:35 05/19/15 Guys, PLEASE, no petroleum distillates on rubber. Petroleum - Zuberman 23:13:14 05/19/15 what about just plain old lube, water based? (n/m) - YlwPrlZTT 00:22:39 05/20/15 You mean like K-Y Jelly? Sorry, all I can recommend is - Zuberman 08:39:44 05/20/15 Vasoline on the injectors orings is the way to go. - Woody75 (Denver) 10:10:11 05/20/15 Vaseline is the go-to for the aviation industry too - BlackholeZ 13:44:23 05/20/15 Arent the orings Buna? - -Grimm- 10:58:28 05/20/15 dielectric grease is silicone grease = good for O-rings - Zbullet 11:54:46 05/20/15 Umm... What do you think Gasoline is? - BlackholeZ 13:45:40 05/20/15 So are you guys saying silicone spray would be worse for - Zuberman 01:24:56 05/24/15 Finish looks nice... Paint or powdercoat? (n/m) - ZXoltan 08:54:53 05/20/15 Engine enamel. (n/m) - YlwPrlZTT 13:19:19 05/20/15 I think you have the rubber parts up-side down. - Woody75 (Denver) 10:07:58 05/20/15 ^^ Agree ^^ (n/m) - ttz'in (norcal) 11:56:55 05/20/15 Are you sure? I didn't even notice how the old ones were - YlwPrlZTT 13:24:55 05/20/15 Yes, soft side down. (n/m) - Woody75 (Denver) 13:26:00 05/20/15 ok thank you. (n/m) - YlwPrlZTT 13:29:27 05/20/15 Ahh crap - BlackholeZ 13:47:02 05/20/15
Post a Followup	You cannot reply to this message because you are not logged in.