Subject	Re: A bad MAF will not throw an ECU code if signal is in range
Posted by	iamdan012 on November 02, 2013 at 9:09 PM
	This message has been viewed 274 times.
In Reply To	A bad MAF will not throw an ECU code if signal is in range posted by Zvil (FL) on November 02, 2013 at 08:46 PM
Message	I believe I checked the maf and it was working correctly and I cant find anyone with a TT around the Charlotte area so I'm kinda stuck as far as my decision goes. Either buy new parts that may or may not solve it or take it to a shop and hope they can diagnose it for me. I've been pondering on the thought of fuel pump..that's the only thing I can think of I haven't checked is the fuel pressure. All cylinders are firing, it's getting fuel but it may not be enough?
Follow Ups	I am at wits end with my dream car, help? - iamdan012 15:21:36 11/02/13 A Z32 specialty shop will be money well spent. - zellamay 15:33:08 11/02/13 Re: I am at wits end with my dream car, help? - iamdan012 20:23:09 11/02/13 Swap out the ecu for a known working one... - 280ZuL8R 20:35:16 11/02/13 This is where I'd start too. If that doesn't do it, swap - ThunderZ 21:08:26 11/02/13 Re: This is where I'd start too. If that doesn't do it, swap - iamdan012 21:14:07 11/02/13 Yup... & keep the tools to replace those parts in the Z. - ThunderZ 12:29:38 11/03/13 A bad MAF will not throw an ECU code if signal is in range - Zvil (FL) 20:46:18 11/02/13 Re: A bad MAF will not throw an ECU code if signal is in range - iamdan012 21:09:54 11/02/13 Well here's what happened to me - Zvil (FL) 18:22:53 11/03/13 * all the compenents tested "perfectly" according to the FSM - Zvil (FL) 18:25:52 11/03/13 Re: I am at wits end with my dream car, help? - Rasta420 06:16:43 11/03/13 I agree with Rasta... see these links for good guides - Medallion Man 08:18:10 11/03/13 Re: I agree with Rasta... see these links for good guides - iamdan012 14:10:37 11/03/13 Re: Re: I am at wits end with my dream car, help? - iamdan012 14:09:13 11/03/13 it could be your engine harness - 300ZMang 14:21:55 11/03/13 Re: it could be your engine harness - iamdan012 15:18:04 11/03/13 Re: Re: it could be your engine harness - Rasta420 15:19:40 11/03/13 brittle, splice and solder... sounds like a possible answer! (n/m) - 300ZMang 16:00:14 11/03/13 is it a hot vs cold hesitation? - 300ZMang 16:17:11 11/03/13 Re: is it a hot vs cold hesitation? - iamdan012 18:14:40 11/03/13 Re: Re: is it a hot vs cold hesitation? - Rasta420 06:33:32 11/04/13 Re: Re: Re: is it a hot vs cold hesitation? - iamdan012 18:16:08 11/04/13 Re: it could be your engine harness - iamdan012 15:48:22 11/03/13 Re: Re: Re: I am at wits end with my dream car, help? - Rasta420 16:59:08 11/03/13 Have you performed the power balance test? - doug8867 10:52:02 11/03/13 just to confrim.. have you checked / replaced the igniter - Medallion Man 03:40:42 11/04/13 Have you checked fuel pressure? - WhiTTe Z (NY) 16:46:16 11/04/13 Re: Have you checked fuel pressure? - iamdan012 18:17:21 11/04/13 Re: Re: Have you checked fuel pressure? - Rasta420 18:28:56 11/04/13 Re: Re: Re: Have you checked fuel pressure? - iamdan012 12:21:18 11/05/13 Re: I am at wits end with my dream car, help? - TheDevilZX 07:12:32 11/06/13
Post a Followup	You cannot reply to this message because you are not logged in.