Subject	Doubt those are the issue
Posted by	MidLifeZ (DFW) on November 19, 2012 at 3:29 PM
	This message has been viewed 227 times.
In Reply To	2 thoughts posted by Zvil (FL) on November 19, 2012 at 01:03 PM
Message	1. MC is known good 2. Slave is new 3. No leaks anywhere 4. Clutch is known Z32 one, bought from Coz and has worked fine up until this week. Guess is needs bled better, as temps went down exacerbated the air issue.. _______________________________________________________________________________________ Z SOLD 02.17.2007, Reacquired 11.05.2011 !
Follow Ups	I give up; Clutch bleed or other issue.. - MidLifeZ (DFW) 11:49:29 11/19/12 Are you only bleeding from the slave? - JonnyZ(SoCal) 12:13:16 11/19/12 my theory for why it took longer for you is - Zvil (FL) 13:06:13 11/19/12 That's what I heard, but searching the forum a lot of people - JonnyZ(SoCal) 14:31:14 11/19/12 Try to bench bleed the clutch master cylinder - tt_703 12:37:41 11/19/12 Info on bench bleeding the master cylinder? - MidLifeZ (DFW) 15:27:13 11/19/12 Re: Info on bench bleeding the master cylinder? - tt_703 19:05:31 11/19/12 did you check the pushrod length like I mentioned before? - aliaZ 12:38:40 11/19/12 Pushrod in the slave? No did not ck that.. - MidLifeZ (DFW) 15:25:39 11/19/12 I posted a link in your prior post (n/m) - aliaZ 17:42:02 11/19/12 pushrod in the master - aliaZ 17:44:01 11/19/12 yes, repalced the pivot ball and - MidLifeZ (DFW) 17:55:32 11/19/12 Re: yes, repalced the pivot ball and - aliaZ 18:53:18 11/19/12 plan for tonight.. - MidLifeZ (DFW) 10:03:52 11/20/12 And the saga continues - MidLifeZ (DFW) 11:05:55 11/21/12 Dang! I tried replacing booster on my 91' TT without pulling - Evan_Wright (Ca) 13:30:37 11/21/12 Yeah, I was stunned I got it swapped out too! especially - MidLifeZ (DFW) 14:46:05 11/21/12 2 thoughts - Zvil (FL) 13:03:42 11/19/12 Doubt those are the issue - MidLifeZ (DFW) 15:29:29 11/19/12 just sharing thoughts, if you got it then make it happen ;) (n/m) - Zvil (FL) 15:48:15 11/19/12 Thinking since have SS clutch lines anyway will - MidLifeZ (DFW) 15:42:37 11/19/12 Get a helper, or buy speedbleeder. (n/m) - Summeronthechain (MN) 08:07:24 11/20/12 Explain this a little better? - Joe@ZSpeedperformance 00:01:49 11/22/12 Answers - MidLifeZ (DFW) 09:45:52 11/22/12 considering that it happened suddenly while at a stop light - aliaZ 10:11:04 11/22/12 2nd, could also be a fork/TOB retainer issue. - TriniTT 09:50:13 11/23/12 A couple things: - rojoloco (VA Beach) 04:22:17 11/22/12 Measurements are - MidLifeZ (DFW) 12:09:30 11/22/12 Does your Z still have.. - 90GoldZ 19:30:10 11/22/12 never had it.. AT>MT swap (n/m) - MidLifeZ (DFW) 09:35:20 11/23/12 Re: never had it.. AT>MT swap - Tech@EPR 20:50:50 11/23/12
Post a Followup	You cannot reply to this message because you are not logged in.