Subject	Try to bench bleed the clutch master cylinder
Posted by	tt_703 on November 19, 2012 at 12:37 PM
	This message has been viewed 584 times.
In Reply To	I give up; Clutch bleed or other issue.. posted by MidLifeZ (DFW) on November 19, 2012 at 11:49 AM
Message	I had similar problem , after many attempts and the clutch still will not engage. Finally one time bleeding the MC , problem solved.
Follow Ups	I give up; Clutch bleed or other issue.. - MidLifeZ (DFW) 11:49:29 11/19/12 Are you only bleeding from the slave? - JonnyZ(SoCal) 12:13:16 11/19/12 my theory for why it took longer for you is - Zvil (FL) 13:06:13 11/19/12 That's what I heard, but searching the forum a lot of people - JonnyZ(SoCal) 14:31:14 11/19/12 Try to bench bleed the clutch master cylinder - tt_703 12:37:41 11/19/12 Info on bench bleeding the master cylinder? - MidLifeZ (DFW) 15:27:13 11/19/12 Re: Info on bench bleeding the master cylinder? - tt_703 19:05:31 11/19/12 did you check the pushrod length like I mentioned before? - aliaZ 12:38:40 11/19/12 Pushrod in the slave? No did not ck that.. - MidLifeZ (DFW) 15:25:39 11/19/12 I posted a link in your prior post (n/m) - aliaZ 17:42:02 11/19/12 pushrod in the master - aliaZ 17:44:01 11/19/12 yes, repalced the pivot ball and - MidLifeZ (DFW) 17:55:32 11/19/12 Re: yes, repalced the pivot ball and - aliaZ 18:53:18 11/19/12 plan for tonight.. - MidLifeZ (DFW) 10:03:52 11/20/12 And the saga continues - MidLifeZ (DFW) 11:05:55 11/21/12 Dang! I tried replacing booster on my 91' TT without pulling - Evan_Wright (Ca) 13:30:37 11/21/12 Yeah, I was stunned I got it swapped out too! especially - MidLifeZ (DFW) 14:46:05 11/21/12 2 thoughts - Zvil (FL) 13:03:42 11/19/12 Doubt those are the issue - MidLifeZ (DFW) 15:29:29 11/19/12 just sharing thoughts, if you got it then make it happen ;) (n/m) - Zvil (FL) 15:48:15 11/19/12 Thinking since have SS clutch lines anyway will - MidLifeZ (DFW) 15:42:37 11/19/12 Get a helper, or buy speedbleeder. (n/m) - Summeronthechain (MN) 08:07:24 11/20/12 Explain this a little better? - Joe@ZSpeedperformance 00:01:49 11/22/12 Answers - MidLifeZ (DFW) 09:45:52 11/22/12 considering that it happened suddenly while at a stop light - aliaZ 10:11:04 11/22/12 2nd, could also be a fork/TOB retainer issue. - TriniTT 09:50:13 11/23/12 A couple things: - rojoloco (VA Beach) 04:22:17 11/22/12 Measurements are - MidLifeZ (DFW) 12:09:30 11/22/12 Does your Z still have.. - 90GoldZ 19:30:10 11/22/12 never had it.. AT>MT swap (n/m) - MidLifeZ (DFW) 09:35:20 11/23/12 Re: never had it.. AT>MT swap - Tech@EPR 20:50:50 11/23/12
Post a Followup	You cannot reply to this message because you are not logged in.