Subject	What does your boost controller read in vacuum? It seems
Posted by	5280Z_nightstalker on July 22, 2012 at 11:09 AM
	This message has been viewed 287 times.
In Reply To	Normal idle? posted by Alan(MD/NJ) on July 21, 2012 at 01:54 PM
Message	like it is not low enough but if you have a new engine i guess it could be because it is not sealed tight yet. "Do you guys put the key in "balls down", or up?" -BobbyT 10:28:19 03/06/09
Follow Ups	Normal idle? - Alan(MD/NJ) 13:54:26 07/21/12 Re: Normal idle? - 300ZMang 13:56:05 07/21/12 15.2 would be lean not rich. (n/m) - Evan_Wright (Ca) 14:29:00 07/21/12 with JWT 500 cams - HighPsi (NorCal) 14:47:07 07/21/12 Same cams (n/m) - Alan(MD/NJ) 16:24:12 07/21/12 Re: Normal idle? - Krazyd27(Houston) 14:57:41 07/21/12 10-30 (n/m) - Alan(MD/NJ) 23:12:52 07/21/12 well on topic - JRFITZ 15:09:24 07/21/12 That's the first thing I noticed too - Coldfusown 15:47:28 07/21/12 Car running only a couple minutes (n/m) - Alan(MD/NJ) 16:26:16 07/21/12 if the car was cold, the idle should be rich. - Antihero 23:14:17 07/21/12 You're over 900rpms, you should be 800-850 and smooth. - TriniTT 15:37:03 07/21/12 Re: Normal idle? - ZuL8tr300 21:26:24 07/21/12 Use to offer it to the community - Alan(MD/NJ) 23:10:45 07/21/12 I also have 500cams... - Devin300zx 22:23:09 07/21/12 Yeah like it wants to stall out or something (n/m) - Alan(MD/NJ) 23:11:40 07/21/12 With mine, ~850-900 sounds pretty good. (n/m) - PiotrC70 00:11:39 07/22/12 check your o2's if you idle doesn't always hover around 14.8 (n/m) - Antihero 23:13:27 07/21/12 I got a set of new OEM o2s - Alan(MD/NJ) 23:19:17 07/21/12 absolutely effects idle. - Antihero 10:37:32 07/22/12 Then I'm I already 95% sure of the problem - Alan(MD/NJ) 10:53:37 07/22/12 Code 55- No fault found (n/m) - Alan(MD/NJ) 15:50:42 07/22/12 No code for a "lazy" O2 IIRC~Run O2 test (n/m) - BoneZ (MD) 22:42:29 07/22/12 bad O2`s rarely throw a code (n/m) - aliaZ 07:13:22 07/23/12 correction: warm idle (n/m) - Antihero 11:30:49 07/22/12 What does your boost controller read in vacuum? It seems - 5280Z_nightstalker 11:09:32 07/22/12 if you're running selin, that's about right. That's what its - mkhoid 21:20:26 07/22/12
Post a Followup	You cannot reply to this message because you are not logged in.