Subject	Re: Re: Re: Re: And also wont require a plenum pull to change
Posted by	SammybTT(TN) on June 10, 2012 at 7:41 PM
	This message has been viewed 178 times.
In Reply To	Re: Re: Re: And also wont require a plenum pull to change posted by SammybTT(TN) on June 05, 2012 at 10:47 PM
Message	I have now set up a youtube account where I can upload some videos of the noise. There are a total of 7 videos that start from the the noise not being present when backing out of the garage and noise when I return along with the following day. Youtube is not allowing me to upload all of the videos during one session but I am uploading as allowed. Please send your thoughts regarding this issue. Thanks again for everyone's reply. I just don't want to drive it anymore until I am confident that this will not harm my engine. Cheers! [ http://youtu.be/LJEQGsIkEC8 ]
Follow Ups	Noisy hydraulic lifter help after rebuild - SammybTT(TN) 10:23:58 06/03/12 Are you sure it's not the VTC Springs instead? (n/m) - ZTicket(Dallas) 13:30:29 06/03/12 Re: Are you sure it's not the VTC Springs instead? - SammybTT(TN) 20:26:10 06/03/12 Did you replace the intake cam gears with BDE's or new ones? (n/m) - ZXoltan 04:45:40 06/04/12 Re: Did you replace the intake cam gears with BDE's or new ones? - SammybTT(TN) 09:14:22 06/04/12 Re: Re: Did you replace the intake cam gears with BDE's or new ones? - SammybTT(TN) 09:19:51 06/04/12 And also wont require a plenum pull to change - ZXoltan 16:05:19 06/04/12 Re: And also wont require a plenum pull to change - SammybTT(TN) 18:22:37 06/04/12 Re: Re: And also wont require a plenum pull to change - SammybTT(TN) 21:27:32 06/04/12 Re: Re: Re: And also wont require a plenum pull to change - SammybTT(TN) 21:43:22 06/05/12 Re: Re: Re: And also wont require a plenum pull to change - SammybTT(TN) 22:47:44 06/05/12 Re: Re: Re: Re: And also wont require a plenum pull to change - SammybTT(TN) 19:41:34 06/10/12 Re: Re: Re: Re: And also wont require a plenum pull to change - SammybTT(TN) 20:35:09 06/10/12 Re: Re: Re: Did you replace the intake cam gears with BDE's or new ones? - SammybTT(TN) 22:10:31 06/06/12 Re: Re: Re: Re: Did you replace the intake cam gears with BDE's or new ones? - SammybTT(TN) 21:45:36 06/07/12 I would think a side by side comparison with a stethoscope - ZTicket(Dallas) 06:13:11 06/04/12 Re: I would think a side by side comparison with a stethoscope - SammybTT(TN) 09:15:21 06/04/12 Hope u get it figured out. Please report back when you do... (n/m) - ZXoltan 20:14:06 06/03/12 Re: Hope u get it figured out. Please report back when you do... - SammybTT(TN) 09:16:36 06/04/12
Post a Followup	You cannot reply to this message because you are not logged in.