Subject	No leakage at all.
Posted by	rojoloco (VA Beach) on April 29, 2012 at 3:23 PM
	This message has been viewed 183 times.
In Reply To	Maybe the seal on the MC is shot and letting air in? posted by my91z on April 29, 2012 at 03:05 PM
Message	The fluid level stays the same. As for the MC, it appears to be relatively new. I got the Z back in 2007 and it was the one part in the engine bay that didn't have any grime on it which tells me it was replaced at some point. I know I replaced the slave cylinder as well as the slave line a couple years back as well. ----------------------------------------------------- Never Play Leapfrog With A Unicorn!!! Do yourself a favor and just worry about your own car. I don't see what everyone is so worried about anyway. If someone else wants to perform a modification that you believe will destroy the value, cheapen the Z32 or whatever you can't sit on your hands about, wouldn't that make your tastefully-modified, white bread Z32 more rare and valuable? -- BradZ (FL) on December 23, 2007 at 12:19 PM The unicorn gets its revenge... -- Scotts94z32 on September 19, 2006 at 11:12 AM CLICK FOR DETAILS ABOUT BUYING A ZAMA POSTER!!!!
Follow Ups	Clutch bleed fail - rojoloco (VA Beach) 14:49:09 04/29/12 Maybe the seal on the MC is shot and letting air in? - my91z 15:05:59 04/29/12 No leakage at all. - rojoloco (VA Beach) 15:23:23 04/29/12 One of the bleeders not holding tight and sucking air >> - my91z 15:37:49 04/29/12 I've had this bleeders problem too - OverZealous (CT) 16:27:41 04/29/12 Do you have a write-up? (n/m) - rojoloco (VA Beach) 18:49:21 04/29/12 Not a lot to it - install SB into the slave cylinder, - jzack 22:29:11 04/29/12 Gotcha. I've never used a SB. - rojoloco (VA Beach) 05:29:24 04/30/12 Cheap Siphon Reverse Bleed Setup - OverZealous (CT) 22:16:38 04/30/12 Thanks! I'll have to try this method. - rojoloco (VA Beach) 09:56:09 05/01/12 Did you get my email? (n/m) - my91z 16:16:45 05/01/12 If it was sent today, not yet. I replied to one this morning - rojoloco (VA Beach) 13:43:51 05/02/12 I've gotten good results using a speedbleeders bleeder (n/m) - AHos(Chicago) 18:54:45 04/29/12 If you can't even shift the car into gear there would - doug8867 21:00:03 05/01/12 I've gotten conflicting info on the clutch booster. - rojoloco (VA Beach) 13:47:00 05/02/12 Agree that booster is not likely to cause your - doug8867 15:13:54 05/02/12 I can try it. - rojoloco (VA Beach) 05:56:39 05/03/12 You had me at: - doug8867 08:20:34 05/03/12 That still leaves a few unanswered questions though. - rojoloco (VA Beach) 11:52:34 05/03/12 Not sure. I had times where I could shift like butter - doug8867 14:40:06 05/03/12 I checked for fluid at the firewall today. - rojoloco (VA Beach) 20:18:49 05/03/12 I would thoroughly clean you slave of wetness, then - doug8867 07:03:45 05/04/12 The slave better not be dead. - rojoloco (VA Beach) 09:11:13 05/04/12 Still trying to picture how a LOT of oil could work itself - doug8867 10:20:23 05/04/12 Now you can fully understand my confusion. - rojoloco (VA Beach) 10:33:13 05/04/12 The pedal adjustment didn't do squat. - rojoloco (VA Beach) 22:18:35 05/04/12 Did you clean your slave first and then inspect - doug8867 09:44:12 05/07/12 Yeah, I cleaned it first. - rojoloco (VA Beach) 08:32:05 05/09/12 Forgot to answer your question about rebuilding MC. - doug8867 11:44:13 05/03/12
Post a Followup	You cannot reply to this message because you are not logged in.