Subject	Ya thats the weird part. There is suppose to be a 4mm
Posted by	5280Z_nightstalker on May 11, 2011 at 10:14 PM
	This message has been viewed 133 times.
In Reply To	But isn't the tensioner too tight? posted by Serg300zx on May 11, 2011 at 10:10 PM
Message	gap when you install the belt then you remove the bolt to let the tensioner put tension on the belt to keep it tight. If anything the gap should increase over time not shrink so that is why everyone THOUGHT the bolt was still in place because the gap should have not shrunk to the point of almost fully closed "Do you guys put the key in "balls down", or up?" -BobbyT 10:28:19 03/06/09
Follow Ups	For all the Z Gurus.. - Serg300zx 21:18:23 05/11/11 Well... - Stadsport (PHX) 21:23:48 05/11/11 wouldn't that be too loose? - 300redtt 21:33:33 05/11/11 Nope, too tight - Stadsport (PHX) 21:55:59 05/11/11 so then his whole tensioning bracket is bolted too far over? - 300redtt 05:54:00 05/12/11 After reading post below i think i have better understanding - 300redtt 06:06:26 05/12/11 Thanks, - Serg300zx 21:35:55 05/11/11 2nd on replacing everything. Then you know it's good. (n/m) - Ziceman(East TN) 21:40:30 05/11/11 Is there a screw holding the tensioner down? If not, - Barry (NJ) 21:36:23 05/11/11 What do you mean? - Serg300zx 21:41:17 05/11/11 There's a screw used to completely close the tensioner - Stadsport (PHX) 21:51:00 05/11/11 Pic inside--> - Serg300zx 22:01:47 05/11/11 no actually there isnt suppose to be but we thought there - 5280Z_nightstalker 22:06:08 05/11/11 But isn't the tensioner too tight? - Serg300zx 22:10:27 05/11/11 Ya thats the weird part. There is suppose to be a 4mm - 5280Z_nightstalker 22:14:53 05/11/11 Just to clarify.. - Stadsport (PHX) 22:17:13 05/11/11 Re: Pic inside--> - CmyZ 22:09:18 05/11/11 That's it. - Stadsport (PHX) 22:13:17 05/11/11 Got'cha ;) - Serg300zx 22:22:18 05/11/11 Probably not, but... - Stadsport (PHX) 22:27:43 05/11/11 Will take the advice! - Serg300zx 22:30:12 05/11/11 Absolutely - Stadsport (PHX) 22:35:48 05/11/11 Thats one way to throw it together lol. - 5280Z_nightstalker 21:55:07 05/11/11 The bolts gone.... - Serg300zx 22:04:54 05/11/11 ****** update**** - Serg300zx 22:59:57 05/11/11 That looks better. (n/m) - ZTurboFan 23:15:24 05/11/11 Did you measure it? Actually looks a little wide! lol (n/m) - Stadsport (PHX) 23:26:25 05/11/11 Yes I did. Its almost at 5mm. - Serg300zx 01:31:16 05/12/11 What do you mean? The tensioner itself or the little bolt? (n/m) - Stadsport (PHX) 18:14:50 05/12/11 This might help btw... - Stadsport (PHX) 18:16:47 05/12/11 found this just today. should be really helpful to you - PhilH 01:00:20 05/15/11 as far as when to replace.. why not just do it now ? - PhilH 01:02:54 05/15/11
Post a Followup	You cannot reply to this message because you are not logged in.