Subject	What do you mean?
Posted by	Serg300zx on May 11, 2011 at 9:41 PM
	This message has been viewed 109 times.
In Reply To	Is there a screw holding the tensioner down? If not, posted by Barry (NJ) on May 11, 2011 at 09:36 PM
Message	Yes the tensioner is held down to the block with screws. Or is there another screw i need to be aware of?
Follow Ups	For all the Z Gurus.. - Serg300zx 21:18:23 05/11/11 Well... - Stadsport (PHX) 21:23:48 05/11/11 wouldn't that be too loose? - 300redtt 21:33:33 05/11/11 Nope, too tight - Stadsport (PHX) 21:55:59 05/11/11 so then his whole tensioning bracket is bolted too far over? - 300redtt 05:54:00 05/12/11 After reading post below i think i have better understanding - 300redtt 06:06:26 05/12/11 Thanks, - Serg300zx 21:35:55 05/11/11 2nd on replacing everything. Then you know it's good. (n/m) - Ziceman(East TN) 21:40:30 05/11/11 Is there a screw holding the tensioner down? If not, - Barry (NJ) 21:36:23 05/11/11 What do you mean? - Serg300zx 21:41:17 05/11/11 There's a screw used to completely close the tensioner - Stadsport (PHX) 21:51:00 05/11/11 Pic inside--> - Serg300zx 22:01:47 05/11/11 no actually there isnt suppose to be but we thought there - 5280Z_nightstalker 22:06:08 05/11/11 But isn't the tensioner too tight? - Serg300zx 22:10:27 05/11/11 Ya thats the weird part. There is suppose to be a 4mm - 5280Z_nightstalker 22:14:53 05/11/11 Just to clarify.. - Stadsport (PHX) 22:17:13 05/11/11 Re: Pic inside--> - CmyZ 22:09:18 05/11/11 That's it. - Stadsport (PHX) 22:13:17 05/11/11 Got'cha ;) - Serg300zx 22:22:18 05/11/11 Probably not, but... - Stadsport (PHX) 22:27:43 05/11/11 Will take the advice! - Serg300zx 22:30:12 05/11/11 Absolutely - Stadsport (PHX) 22:35:48 05/11/11 Thats one way to throw it together lol. - 5280Z_nightstalker 21:55:07 05/11/11 The bolts gone.... - Serg300zx 22:04:54 05/11/11 ****** update**** - Serg300zx 22:59:57 05/11/11 That looks better. (n/m) - ZTurboFan 23:15:24 05/11/11 Did you measure it? Actually looks a little wide! lol (n/m) - Stadsport (PHX) 23:26:25 05/11/11 Yes I did. Its almost at 5mm. - Serg300zx 01:31:16 05/12/11 What do you mean? The tensioner itself or the little bolt? (n/m) - Stadsport (PHX) 18:14:50 05/12/11 This might help btw... - Stadsport (PHX) 18:16:47 05/12/11 found this just today. should be really helpful to you - PhilH 01:00:20 05/15/11 as far as when to replace.. why not just do it now ? - PhilH 01:02:54 05/15/11
Post a Followup	You cannot reply to this message because you are not logged in.