Subject	If an auto tranny (and tranny is attached) -- remove
Posted by	jzack on April 08, 2011 at 7:40 PM
	This message has been viewed 152 times.
In Reply To	How is the bolt tightened on the Auto tranny? (n/m) posted by Havoc300 (Chicago) on April 08, 2011 at 03:49 PM
Message	the start motor and wedge a screwdriver in the flywheel teeth inside. Not all that hard to do just be sure the battery is fully disconnected before messing with the starter wires...
Follow Ups	Crank Pulley bolt removal.. - Havoc300 (Chicago) 14:05:12 04/07/11 Lefty loosie baby! (n/m) - BoneZ 14:08:48 04/07/11 Thanks! 3 days & I'm still trying. No impact wrench. (n/m) - Havoc300 (Chicago) 14:24:50 04/07/11 breaker bar? (n/m) - BoneZ 14:51:29 04/07/11 Use a long pipe or breaker bar.. - KongZTT GT28RS MD 14:51:42 04/07/11 I thought I was the only one to try that (n/m) - ZiNnYc 17:50:28 04/07/11 we "GTFO'ers" think alike :) (n/m) - KongZTT GT28RS MD 19:13:44 04/07/11 hei. crank pulley bolt...GTFO (n/m) - ZiNnYc 21:45:54 04/07/11 I just removed mine last night. I spraying penetrating lube - Samuel (Dallas) 15:59:09 04/07/11 Hey Samuel... Check Email. (n/m) - Havoc300 (Chicago) 16:38:25 04/07/11 I would use a 1/2" drive ratchet on it.. - KongZTT GT28RS MD 19:17:07 04/07/11 Fuel pump relay out of course! (n/m) - BoneZ 20:25:03 04/07/11 yep. or just disconnect PTU or CAS - KongZTT GT28RS MD 20:47:16 04/07/11 Yeah, wouldn't want to see the "I tried this and..." post (n/m) - BoneZ 21:51:01 04/07/11 Bumping the starter is the best method. Put a piece of - zellamay 21:03:21 04/07/11 Worked like a champ. Thanks Guys!! Now..... - Havoc300 (Chicago) 10:20:22 04/08/11 The key on the crank and pulley will keep it from turning. (n/m) - Woody75 (Denver) 11:48:30 04/08/11 Need to do this on my Automatic trans car. How to tighten? (n/m) - not4resaleZ 12:20:33 04/08/11 Should be able to do in park. (n/m) - KongZTT GT28RS MD 14:19:36 04/08/11 Use E-brake too (n/m) - KongZTT GT28RS MD 14:20:34 04/08/11 I always hate to load the trans in park. I may remove the - not4resaleZ 14:28:29 04/08/11 Guess there is also the "Belt Wrap" method. (n/m) - not4resaleZ 14:33:22 04/08/11 You aren't putting THAT much stress on the trans.. - KongZTT GT28RS MD 15:07:19 04/08/11 Which I don't do. I use the parking brake for that. - not4resaleZ 16:30:03 04/08/11 put them on the ground :).. - KongZTT GT28RS MD 19:33:32 04/08/11 no...you'll just spin the torque converter (n/m) - aliaZ 06:48:50 04/10/11 Put car in 5th gear.. (n/m) - KongZTT GT28RS MD 14:19:21 04/08/11 oh yea.. and use E-brake. (n/m) - KongZTT GT28RS MD 14:20:12 04/08/11 How is the bolt tightened on the Auto tranny? (n/m) - Havoc300 (Chicago) 15:49:50 04/08/11 I just answered this above.. use your ebrake.. - KongZTT GT28RS MD 16:29:21 04/08/11 Won't work, The torque converter slips. (n/m) - Fast300 22:54:34 04/08/11 If an auto tranny (and tranny is attached) -- remove - jzack 19:40:16 04/08/11 Just use the e brake.. why go through all that? (n/m) - KongZTT GT28RS MD 19:48:46 04/08/11 Because it won't work the torque converter will still slip. - Fast300 22:50:23 04/08/11 I didn't even think of that.. I don't own an auto.. - KongZTT GT28RS MD 13:34:23 04/09/11
Post a Followup	You cannot reply to this message because you are not logged in.