Subject	put them on the ground :)..
Posted by	KongZTT GT28RS MD on April 08, 2011 at 7:33 PM
	This message has been viewed 144 times.
In Reply To	Which I don't do. I use the parking brake for that. posted by not4resaleZ on April 08, 2011 at 04:30 PM
Message	just kidding.. Well if your E-brake doesn't hold for some reason (not adjusted properly etc) Just have someone hold one of the rear tires.. it doesn't take too much to hold it if all you are doing is torquing the crank bolt. _________________________________________________________________________ ~~~ Sig starts below ~~~ ================================================================= NO, This picture is not photoshopped. MySpace for those who have em' AIM:Shawn300zxTT "-Any closeups on the nuts? - zboost(tx) 19:17:53 08/08/05 -Not really something you want to ask another man about... (n/m) - LordZ 19:24:00 08/08/05" "I just took 45 min and scrubbed the heck out of my rear" teambushido(San Diego, CA) 19:24:51 12/11/04 -1991 Stage _ TT 5spd (Upgraded to hell and back) -1990 Super White 2+2 Na Stage 3 Auto (Deceased :( ) -1990 Cherry Red Pearl ,Auto Coupe (Parts car) -1990 11 Sec Eagle Talon Tsi AWD, (SOLD!) -2001 Ford F-150 Crew cab, 5.4 Triton v8.. Tow bitch -1997 Acura 2.2 CL, 5spd. Daily Driver.. great little car! -2004 Honda CBR 600RR (Candy blue, FOR SALE)
Follow Ups	Crank Pulley bolt removal.. - Havoc300 (Chicago) 14:05:12 04/07/11 Lefty loosie baby! (n/m) - BoneZ 14:08:48 04/07/11 Thanks! 3 days & I'm still trying. No impact wrench. (n/m) - Havoc300 (Chicago) 14:24:50 04/07/11 breaker bar? (n/m) - BoneZ 14:51:29 04/07/11 Use a long pipe or breaker bar.. - KongZTT GT28RS MD 14:51:42 04/07/11 I thought I was the only one to try that (n/m) - ZiNnYc 17:50:28 04/07/11 we "GTFO'ers" think alike :) (n/m) - KongZTT GT28RS MD 19:13:44 04/07/11 hei. crank pulley bolt...GTFO (n/m) - ZiNnYc 21:45:54 04/07/11 I just removed mine last night. I spraying penetrating lube - Samuel (Dallas) 15:59:09 04/07/11 Hey Samuel... Check Email. (n/m) - Havoc300 (Chicago) 16:38:25 04/07/11 I would use a 1/2" drive ratchet on it.. - KongZTT GT28RS MD 19:17:07 04/07/11 Fuel pump relay out of course! (n/m) - BoneZ 20:25:03 04/07/11 yep. or just disconnect PTU or CAS - KongZTT GT28RS MD 20:47:16 04/07/11 Yeah, wouldn't want to see the "I tried this and..." post (n/m) - BoneZ 21:51:01 04/07/11 Bumping the starter is the best method. Put a piece of - zellamay 21:03:21 04/07/11 Worked like a champ. Thanks Guys!! Now..... - Havoc300 (Chicago) 10:20:22 04/08/11 The key on the crank and pulley will keep it from turning. (n/m) - Woody75 (Denver) 11:48:30 04/08/11 Need to do this on my Automatic trans car. How to tighten? (n/m) - not4resaleZ 12:20:33 04/08/11 Should be able to do in park. (n/m) - KongZTT GT28RS MD 14:19:36 04/08/11 Use E-brake too (n/m) - KongZTT GT28RS MD 14:20:34 04/08/11 I always hate to load the trans in park. I may remove the - not4resaleZ 14:28:29 04/08/11 Guess there is also the "Belt Wrap" method. (n/m) - not4resaleZ 14:33:22 04/08/11 You aren't putting THAT much stress on the trans.. - KongZTT GT28RS MD 15:07:19 04/08/11 Which I don't do. I use the parking brake for that. - not4resaleZ 16:30:03 04/08/11 put them on the ground :).. - KongZTT GT28RS MD 19:33:32 04/08/11 no...you'll just spin the torque converter (n/m) - aliaZ 06:48:50 04/10/11 Put car in 5th gear.. (n/m) - KongZTT GT28RS MD 14:19:21 04/08/11 oh yea.. and use E-brake. (n/m) - KongZTT GT28RS MD 14:20:12 04/08/11 How is the bolt tightened on the Auto tranny? (n/m) - Havoc300 (Chicago) 15:49:50 04/08/11 I just answered this above.. use your ebrake.. - KongZTT GT28RS MD 16:29:21 04/08/11 Won't work, The torque converter slips. (n/m) - Fast300 22:54:34 04/08/11 If an auto tranny (and tranny is attached) -- remove - jzack 19:40:16 04/08/11 Just use the e brake.. why go through all that? (n/m) - KongZTT GT28RS MD 19:48:46 04/08/11 Because it won't work the torque converter will still slip. - Fast300 22:50:23 04/08/11 I didn't even think of that.. I don't own an auto.. - KongZTT GT28RS MD 13:34:23 04/09/11
Post a Followup	You cannot reply to this message because you are not logged in.