Subject	I just removed mine last night. I spraying penetrating lube
Posted by	Samuel (Dallas) on April 07, 2011 at 3:59 PM
	This message has been viewed 209 times.
In Reply To	Crank Pulley bolt removal.. posted by Havoc300 (Chicago) on April 07, 2011 at 02:05 PM
Message	I just removed mine last night. I spraying penetrating lube on the bolt and let it set for a day or two and then used the handle from my JEGS jack to slip over the 3/8 ratchet handle (This is what KongZTT means by using a 'breaker bar') and turn the bolt counter clock wise to remove it. I can email you pics later tonight if you like. Thanks, Samuel (Dallas)
Follow Ups	Crank Pulley bolt removal.. - Havoc300 (Chicago) 14:05:12 04/07/11 Lefty loosie baby! (n/m) - BoneZ 14:08:48 04/07/11 Thanks! 3 days & I'm still trying. No impact wrench. (n/m) - Havoc300 (Chicago) 14:24:50 04/07/11 breaker bar? (n/m) - BoneZ 14:51:29 04/07/11 Use a long pipe or breaker bar.. - KongZTT GT28RS MD 14:51:42 04/07/11 I thought I was the only one to try that (n/m) - ZiNnYc 17:50:28 04/07/11 we "GTFO'ers" think alike :) (n/m) - KongZTT GT28RS MD 19:13:44 04/07/11 hei. crank pulley bolt...GTFO (n/m) - ZiNnYc 21:45:54 04/07/11 I just removed mine last night. I spraying penetrating lube - Samuel (Dallas) 15:59:09 04/07/11 Hey Samuel... Check Email. (n/m) - Havoc300 (Chicago) 16:38:25 04/07/11 I would use a 1/2" drive ratchet on it.. - KongZTT GT28RS MD 19:17:07 04/07/11 Fuel pump relay out of course! (n/m) - BoneZ 20:25:03 04/07/11 yep. or just disconnect PTU or CAS - KongZTT GT28RS MD 20:47:16 04/07/11 Yeah, wouldn't want to see the "I tried this and..." post (n/m) - BoneZ 21:51:01 04/07/11 Bumping the starter is the best method. Put a piece of - zellamay 21:03:21 04/07/11 Worked like a champ. Thanks Guys!! Now..... - Havoc300 (Chicago) 10:20:22 04/08/11 The key on the crank and pulley will keep it from turning. (n/m) - Woody75 (Denver) 11:48:30 04/08/11 Need to do this on my Automatic trans car. How to tighten? (n/m) - not4resaleZ 12:20:33 04/08/11 Should be able to do in park. (n/m) - KongZTT GT28RS MD 14:19:36 04/08/11 Use E-brake too (n/m) - KongZTT GT28RS MD 14:20:34 04/08/11 I always hate to load the trans in park. I may remove the - not4resaleZ 14:28:29 04/08/11 Guess there is also the "Belt Wrap" method. (n/m) - not4resaleZ 14:33:22 04/08/11 You aren't putting THAT much stress on the trans.. - KongZTT GT28RS MD 15:07:19 04/08/11 Which I don't do. I use the parking brake for that. - not4resaleZ 16:30:03 04/08/11 put them on the ground :).. - KongZTT GT28RS MD 19:33:32 04/08/11 no...you'll just spin the torque converter (n/m) - aliaZ 06:48:50 04/10/11 Put car in 5th gear.. (n/m) - KongZTT GT28RS MD 14:19:21 04/08/11 oh yea.. and use E-brake. (n/m) - KongZTT GT28RS MD 14:20:12 04/08/11 How is the bolt tightened on the Auto tranny? (n/m) - Havoc300 (Chicago) 15:49:50 04/08/11 I just answered this above.. use your ebrake.. - KongZTT GT28RS MD 16:29:21 04/08/11 Won't work, The torque converter slips. (n/m) - Fast300 22:54:34 04/08/11 If an auto tranny (and tranny is attached) -- remove - jzack 19:40:16 04/08/11 Just use the e brake.. why go through all that? (n/m) - KongZTT GT28RS MD 19:48:46 04/08/11 Because it won't work the torque converter will still slip. - Fast300 22:50:23 04/08/11 I didn't even think of that.. I don't own an auto.. - KongZTT GT28RS MD 13:34:23 04/09/11
Post a Followup	You cannot reply to this message because you are not logged in.