Subject	You dont have to worry about using somthing that handles PSI
Posted by	KongZTT GT28RS MD on February 01, 2011 at 9:25 AM
	This message has been viewed 104 times.
In Reply To	Anyone ever used exhaust hose as inlet piping? posted by evan_aggie on February 01, 2011 at 08:03 AM
Message	For the inlet piping.. It will see no boost, only vacuum. If you feel that you want to construct some inlet piping yourself. I suggest you go to [ http://www.mandrel-bends.com ] they are the cheapest I have ever found for mandrel bent piping. But your required mandrel bends from there, cut/weld etc. Why not just mill the compressor down and make a flange like the 530bb? I went through all this a couple years ago with my GT28R turbos.. There are several ways to do this. I ended up making adapter flanges from 1/4" plate steel, powdercoating, using gasket maker/stock gaskets, bolting to turbo compressor housing, then bolting stock inlet to the adapter. _________________________________________________________________________ ~~~ Sig starts below ~~~ ================================================================= NO, This picture is not photoshopped. MySpace for those who have em' AIM:Shawn300zxTT "-Any closeups on the nuts? - zboost(tx) 19:17:53 08/08/05 -Not really something you want to ask another man about... (n/m) - LordZ 19:24:00 08/08/05" "I just took 45 min and scrubbed the heck out of my rear" teambushido(San Diego, CA) 19:24:51 12/11/04 -1991 Stage _ TT 5spd (Upgraded to hell and back) -1990 Super White 2+2 Na Stage 3 Auto (Deceased :( ) -1990 Cherry Red Pearl ,Auto Coupe (Parts car) -1990 11 Sec Eagle Talon Tsi AWD, (SOLD!) -2001 Ford F-150 Crew cab, 5.4 Triton v8.. Tow bitch -1997 Acura 2.2 CL, 5spd. Daily Driver.. great little car! -2004 Honda CBR 600RR (Candy blue, FOR SALE)
Follow Ups	custom compressor inlet hose - evan_aggie 21:55:45 01/31/11 It would have been easier if you got GT2560R (aka gt28R) - KongZTT GT28RS MD 00:35:57 02/01/11 Yeah, I saw those on atpturbo. The only problem is that - evan_aggie 07:52:58 02/01/11 The flange they use has a taper in the center. (n/m) - KongZTT GT28RS MD 09:27:14 02/01/11 You also could cut the flanges off the stock inlet piping - KongZTT GT28RS MD 09:35:20 02/01/11 How about a muffler shop? I don't anyone in particular. (n/m) - evan_aggie 09:43:15 02/01/11 They may be able to.. but look into the phone book for - KongZTT GT28RS MD 10:13:32 02/01/11 Anyone ever used exhaust hose as inlet piping? - evan_aggie 08:03:43 02/01/11 You dont have to worry about using somthing that handles PSI - KongZTT GT28RS MD 09:25:21 02/01/11 Oh right. Well, anyway, it was just a thought. You are - evan_aggie 09:47:47 02/01/11 I am pretty sure the 2.5" will clamp down to a smaller size - KongZTT GT28RS MD 10:12:30 02/01/11 53mm inner diameter is identical for 2560 and 2554. - evan_aggie 11:30:19 02/01/11 I did like Kong suggested. Use the ATP flanges! - greyzx (now blue) 17:02:57 02/03/11
Post a Followup	You cannot reply to this message because you are not logged in.