Subject	It would have been easier if you got GT2560R (aka gt28R)
Posted by	KongZTT GT28RS MD on February 01, 2011 at 12:35 AM
	This message has been viewed 177 times.
In Reply To	custom compressor inlet hose posted by evan_aggie on January 31, 2011 at 09:55 PM
Message	The (stock piping) inlet flange would just need to be cut/welded in proper orientation. at ATP turbo.. they sell hose bib--> 2 bolt configuration adapters. if you want to go that route. This way you will just use a coupler (possibly cut in half to make it shorter) to attach this adapter. Then just bolt the compressor inlet to this new flange. here is what I am talking about.. :[ http://www.atpturbo.com/mm5/merchant.mvc?Screen=PROD&Store_Code=tp&Product_Code=ATP-FLA-012&Category_Code=FLA ] You may be able to cut and even out the stock compressor inlet pipes to be round and use a coupler to the GT2554 turbo inlet. You will probably have to machine/grind down a bit of the motor mount to clear the inlet pipes. For the compressor outlet.. (I am not sure if they are orientated like the GT28R turbos) you can probably just make either an adapter plate or cut weld it (I dont recommend welding the inlet due to possible warpage.. the outlet you can get away with cutting and turning to proper angle. Or again.. like the inlet adapter sold by ATP.. you can buy a hose bib connection for the outlet but you would need one side to have a 90^ coupler. Just sit down and look at everything you need. If you have access to a machine shop.. you can mill the inlets down flat, then bolt an adapter flange (similar to how jwt does the 530s, 700bb etc) _________________________________________________________________________ ~~~ Sig starts below ~~~ ================================================================= NO, This picture is not photoshopped. MySpace for those who have em' AIM:Shawn300zxTT "-Any closeups on the nuts? - zboost(tx) 19:17:53 08/08/05 -Not really something you want to ask another man about... (n/m) - LordZ 19:24:00 08/08/05" "I just took 45 min and scrubbed the heck out of my rear" teambushido(San Diego, CA) 19:24:51 12/11/04 -1991 Stage _ TT 5spd (Upgraded to hell and back) -1990 Super White 2+2 Na Stage 3 Auto (Deceased :( ) -1990 Cherry Red Pearl ,Auto Coupe (Parts car) -1990 11 Sec Eagle Talon Tsi AWD, (SOLD!) -2001 Ford F-150 Crew cab, 5.4 Triton v8.. Tow bitch -1997 Acura 2.2 CL, 5spd. Daily Driver.. great little car! -2004 Honda CBR 600RR (Candy blue, FOR SALE)
Follow Ups	custom compressor inlet hose - evan_aggie 21:55:45 01/31/11 It would have been easier if you got GT2560R (aka gt28R) - KongZTT GT28RS MD 00:35:57 02/01/11 Yeah, I saw those on atpturbo. The only problem is that - evan_aggie 07:52:58 02/01/11 The flange they use has a taper in the center. (n/m) - KongZTT GT28RS MD 09:27:14 02/01/11 You also could cut the flanges off the stock inlet piping - KongZTT GT28RS MD 09:35:20 02/01/11 How about a muffler shop? I don't anyone in particular. (n/m) - evan_aggie 09:43:15 02/01/11 They may be able to.. but look into the phone book for - KongZTT GT28RS MD 10:13:32 02/01/11 Anyone ever used exhaust hose as inlet piping? - evan_aggie 08:03:43 02/01/11 You dont have to worry about using somthing that handles PSI - KongZTT GT28RS MD 09:25:21 02/01/11 Oh right. Well, anyway, it was just a thought. You are - evan_aggie 09:47:47 02/01/11 I am pretty sure the 2.5" will clamp down to a smaller size - KongZTT GT28RS MD 10:12:30 02/01/11 53mm inner diameter is identical for 2560 and 2554. - evan_aggie 11:30:19 02/01/11 I did like Kong suggested. Use the ATP flanges! - greyzx (now blue) 17:02:57 02/03/11
Post a Followup	You cannot reply to this message because you are not logged in.