Subject	If it seems like I am adamant about this
Posted by	NytWolf on January 09, 2008 at 10:55 AM
	This message has been viewed 220 times.
In Reply To	Nytwolf why are you so adamant about this? posted by fanta-z on January 08, 2008 at 06:07 PM
Message	It is only because I own 5 other Japanese cars, 2 European cars, and service 5 friends' cars, and ALL (and I mean ALL) their throttle cables have more slack than the amount this procedure would allow. I estimate approximately 1/8" deflection. Manufacturers don't all do it a certain way for no reason. A few of these cars mentioned above are newer cars even. But like Guapo said, if adjusting it that way has been working for years, then so be it. But I'm just voicing my opinion based on what I have seen.
Follow Ups	Accelerator Cable Adjustment Reduced Driveline Kickback - Gordo 93TT Daytona 17:24:33 01/07/08 Thanks. Move to Tech VTF - induetime 17:35:13 01/07/08 A very lucid how to. Bookmarked. Thanks. (n/m) - 240Z FeO2 17:44:17 01/07/08 My car had the same problem. I did the same (reduced - olyar15 17:49:15 01/07/08 Re: Accelerator Cable Adjustment Reduced Driveline Kickback - naZeer (Dallas) 17:57:20 01/07/08 You are on a mission. - Boosted1 18:51:50 01/07/08 Yes I did. New 98+trans, rebuilt diff, 2 ea. drive axles, - Gordo 93TT Daytona 19:40:42 01/07/08 Nice (n/m) - collegeboy 18:53:32 01/07/08 No - NytWolf 21:54:43 01/07/08 There should be some, but not much. I usually adjust - Guapo 22:01:51 01/07/08 There should be about double that amount of slack (n/m) - NytWolf 22:04:21 01/07/08 why? (n/m) - Guapo 22:09:20 01/07/08 Because - NytWolf 22:10:15 01/07/08 Shrug. Been doing it that way for years now, and - Guapo 22:18:34 01/07/08 Same idea as why you adjust your clutch pedal - NytWolf 22:25:18 01/07/08 right. And half a turn is plenty on the throttle cable - Guapo 22:26:24 01/07/08 Not enough slack (n/m) - NytWolf 22:40:13 01/07/08 you're wrong (n/m) - Guapo 22:45:53 01/07/08 You are - NytWolf 23:25:33 01/07/08 lol - Guapo 23:31:10 01/07/08 I agree that you do not want the cable to be so tight as to - Gordo 93TT Daytona 22:16:55 01/07/08 Your procedure still leaves the cable tighter than should be (n/m) - NytWolf 22:26:05 01/07/08 FSM spec says tighten until rod pulley moves, then back off - Gordo 93TT Daytona 08:14:39 01/08/08 Where in FSM? (n/m) - NytWolf 12:07:58 01/08/08 Section FE-2 (n/m) - Gordo 93TT Daytona 13:33:27 01/08/08 Nytwolf why are you so adamant about this? - fanta-z 18:07:25 01/08/08 If it seems like I am adamant about this - NytWolf 10:55:14 01/09/08
Post a Followup	You cannot reply to this message because you are not logged in.