Subject	Guys - strange but on my plenum the #2 injector had
Posted by	jzack on January 08, 2007 at 4:55 PM
	This message has been viewed 303 times.
In Reply To	Injector Dremel method pics for reference posted by Ted (92TT) on January 07, 2007 at 09:24 PM
Message	much more metal going over it then in this picture? Even after I Dremeled it very aggressively --- couldn't get a new hex head bolt into the cap (clearance issues). My point? -- guessing that the manufacturing tolerances between these parts isn't all that close (on the outside runners)? None the less -- this is a nice posting for documenting everything visually! Good job...
Follow Ups	Injector Dremel method pics for reference - Ted (92TT) 21:24:44 01/07/07 Re: Injector Dremel method pics for reference - Nis300owner 22:06:21 01/07/07 What kind of tip did you use on the dremel? (n/m) - cherryz 22:22:30 01/07/07 Coarse sanding drums/bands work best - Ted (92TT) 22:46:18 01/07/07 No, these work better. - Woody75 (Denver) 23:06:06 01/07/07 I stand corrected :-) (n/m) - Ted (92TT) 23:33:36 01/07/07 I found using small cut-off wheels where the - Audioquest 16:28:03 01/08/07 Try the carbide bits for aluminum that Woody linked to - 300zx90 (CO) 16:43:18 01/08/07 Noted, thanks! (n/m) - Audioquest 17:59:44 01/08/07 this - robo (sebring1970) 23:28:36 01/07/07 Yea, i spot replaced #2 and it was a bitch to get out > - WE350Z 01:27:29 01/08/07 Re: Injector Dremel method pics for reference - ZX2NVaus 05:49:31 01/08/07 what is that little tool you are showing to start the - mossyoak 09:41:47 01/08/07 Look closely. It is an angled screwdriver. - Technomancer 09:57:00 01/08/07 Yup, Sears (n/m) - Ted (92TT) 10:58:09 01/08/07 thats what I thought, good idea (n/m) - mossyoak 15:34:03 01/08/07 Extrude hone shouldn't be a problem.. - Ted (92TT) 10:57:34 01/08/07 the best too is an air grinder with carbide bit - CRAZZEPETE. 14:20:49 01/08/07 Vote to Faq these pics?? (n/m) - CRAZZEPETE. 14:22:33 01/08/07 Do you have any idea how thin the wall thickness is in the - Zirvana 16:48:11 01/08/07 No idea, but the casting seems pretty thick - Ted (92TT) 18:47:38 01/08/07 From looking at the upper plenum on my 94TT, I felt that - Zirvana 13:57:34 01/09/07 Guys - strange but on my plenum the #2 injector had - jzack 16:55:20 01/08/07 all i know is was shitting my pants think i would go 2 far. (n/m) - WE350Z 00:00:22 01/09/07 only thing i noticed becuz i am anal and critical > - WE350Z 00:08:12 01/09/07 Yeah - lazer(AK) 15:29:52 01/10/07
Post a Followup	You cannot reply to this message because you are not logged in.