Subject	Nice post! Another safety tip when using that style of
Posted by	Inzane on October 04, 2006 at 9:55 AM
	This message has been viewed 314 times.
In Reply To	clutch replacement...pic heavy posted by naZeer (Dallas) on October 04, 2006 at 08:38 AM
Message	tranny jack. 'Keep your eyes on your front jackstands.' When I did my tranny R&R last fall and was putting the tranny back in there was a point when the tranny was catching on something while I was raising the jack and the car was lifted slightly off the right front jackstand. I only discovered it when my arm bumped the stand and it MOVED... I was like WTH?? A situation I quickly rectified of course. Also, nice tip on the Nismo pilot bearing putting it in the freezer. I had trouble installing mine too and gave up and just used an oem one instead. I hadn't thought to try the freezer trick at the time, but given Mike Smith's and Damon's skepticism about the needle bearings anyways, I wasn't too concerned about whether I installed it or not. Inzane (formerly Z-Jay) Vice President - Edmonton Z Car Club 93 300ZX TT - Stage VI
Follow Ups	clutch replacement...pic heavy - naZeer (Dallas) 08:38:34 10/04/06 Nice writeup. Thanks (n/m) - zzman (nashville) 08:52:58 10/04/06 great writeup w/ pics and tips - bobZtwin (NC) 09:01:48 10/04/06 Nice job!, that's a sexy car you got there (n/m) - BigTDogg (MA) 09:07:44 10/04/06 Great post! - vorpalZ 09:15:09 10/04/06 good writeup - bookmarked (n/m) - spicyZ 09:22:17 10/04/06 Fantastic work! I'm loving the 3 inch bolt trick. (n/m) - Zeus 09:22:56 10/04/06 2nd - wish I knew about that a while back! (n/m) - TT XTZ 09:25:25 10/04/06 Excellent write-up - TT XTZ 09:24:59 10/04/06 Probably obvious, but after 20 min. of trying to get the - BummedOutMonkey 09:26:27 10/04/06 Nice writeup! - Mickie 09:40:37 10/04/06 Great write-up! I wish I'd known about using - Dustin 09:54:37 10/04/06 Nice post! Another safety tip when using that style of - Inzane 09:55:31 10/04/06 whoa! check you out. - LordZ 10:45:12 10/04/06 awesome! i need that tranny jack. - apudapus 11:42:32 10/04/06 Nice! (n/m) - mousersix 12:29:08 10/04/06 OK - question about dropping the exhaust... - jzack 16:54:09 10/04/06 cut what??? - LordZ 17:14:50 10/04/06 Dosen't work so well on a 2+2 , has two hangers in the - jzack 22:22:28 10/04/06 I put the stock ones on and took off 3 times so far - LordZ 20:33:01 10/05/06 thanks for the compliments guys... - naZeer (Dallas) 20:01:43 10/04/06 very good tip, learned this the hard way (n/m) - mousersix 21:35:43 10/04/06 damn, wow - PakiHomBoy 17:17:33 10/04/06 Awesome job. Do you happen to have the part # to - Worm Boy 21:43:32 10/04/06 throw out bearing 30502-45P00 - naZeer (Dallas) 23:26:48 10/04/06
Post a Followup	You cannot reply to this message because you are not logged in.