Subject	You do know those come stock on 'crappy' DSM's right?
Posted by	Bucky Z(Dallas) on September 23, 2002 at 8:21 PM
	This message has been viewed 161 times.
In Reply To	ER, UH, they are TD05-14B's.. Not TD04's... :-/ >>>>> posted by AshsZ (Fab Whore, Ph.D) on September 23, 2002 at 06:59 PM
Message	And they have internal wastegates... They're good for a little over 300 hp on a 1g DSM. They will bolt to the stock manifold, but I think the problem you'll run into is getting the compressor inlet and outlet facing the right directions... I thought about all this when I still had my 1g Talon cause 14b's are a dime a dozen. But I guess somebody like you might be able to get them to work. Later, B.U.C.K.Y.: Biomechanical Unit Calibrated for Killing and Yardwork
Follow Ups	Are there manifolds available for TD04's? - AshsZ (Fab Whore, Ph.D) 18:30:01 09/23/02 pretty sure the Greddy TD04's bolt to stock manifolds (n/m) - 96-2+2TT(Power Supply Racing) 18:33:25 09/23/02 That's nice, but they dont have internal wastegates. - AshsZ (Fab Whore, Ph.D) 18:37:58 09/23/02 Fab Whore, Ph.D (n/m) - genic 18:39:50 09/23/02 shut ur pie hole. :) - AshsZ (Fab Whore, Ph.D) 18:56:02 09/23/02 pvc and duct tape own you :) (n/m) - genic 19:02:28 09/23/02 no, the greddy td04s for the 300zx bolt to stock manis and - FANTAZ(Power Supply Racing) 18:40:58 09/23/02 Well then, that makes them pretty attractive. :) - AshsZ (Fab Whore, Ph.D) 18:55:23 09/23/02 TD04's are rather rare to begin with, not to mention that - Z from Japan 20:18:58 09/23/02 Nice looking website (n/m) - Tennyson (ATL) 20:01:42 09/23/02 TD04s are tiny don't waste your time on them. (n/m) - Carlos Ramirez 18:49:58 09/23/02 ER, UH, they are TD05-14B's.. Not TD04's... :-/ >>>>> - AshsZ (Fab Whore, Ph.D) 18:59:18 09/23/02 oh thats a different story.. - Carlos Ramirez 19:11:29 09/23/02 TD05H-16G versus TD05H-14B versus TD06-20G - Carlos Ramirez 19:12:26 09/23/02 Here is a copy of the compressor maps for both if you like. - Flycaz (MLB, FL) 07:39:32 09/24/02 You do know those come stock on 'crappy' DSM's right? - Bucky Z(Dallas) 20:21:05 09/23/02 Yup. But they're made by Greddy. (n/m) - AshsZ (Fab Whore, Ph.D) 21:31:35 09/23/02 Everything is smaller compared to your 2835 comp housing:-) - George(boostsolutionsinc.net) 00:29:39 09/24/02 Find a set of Greddy manifolds, and get a 16G wheel put in - Chip(GinnMotorsports) 20:31:08 09/23/02 You know that you can get some good GT25 turbos - Chip(GinnMotorsports) 20:32:23 09/23/02 The exh. side will bolt up to our manifold, you just need - NSANY(ATL) 06:46:46 09/24/02
Post a Followup	You cannot reply to this message because you are not logged in.