Subject	Getting ready to do some work... and a surprise find!
Posted by	Woodnutz (PA) on March 22, 2021 at 12:29 PM
	This message has been viewed 1138 times.
Message	Finally getting around to doing some work. Hallman manual boost controller, CZP PTU bracket to clean up/finish previous relocation work, CZP master cylinder brace, reman A/C clutch (thanks, Shaggee, for the share - hopefully it resolves my fuse blowing issue), UR underdrive pulley kit... which I wasn't planning on doing, but you know... while I'm in there... why not? Aaaaand... a little piece you may not notice - alternator stopper nut. Pictures below will explain that one. Also going to try and clean up a bunch under the hood. Specifically around the power steering plumbing. I have a leak and need to pinpoint it. With it cleaned up and clamps tightened, hopefully I'll either stop the leak or at least find it. New parts! Look what I found when I started digging around in preparation for the work a couple weeks ago! Glad I shut the car down when I did. ...and here's the view from above once the radiator was out. Yikes. - Aaron
Follow Ups	Getting ready to do some work... and a surprise find! - Woodnutz (PA) 12:29:48 03/22/21 Oof, good catch. (n/m) - Zeus 13:05:25 03/22/21 Whoa...is that the alternator bolt? Good save! (n/m) - CameronSF 15:34:49 03/22/21 Yep - upper bolt. Belt tension is holding it in place. - Woodnutz (PA) 09:32:33 03/23/21 Nice save - Drk93TT 18:48:20 03/22/21 Yea, I’m taking a risk. Keeping fingers crossed. (n/m) - Woodnutz (PA) 19:42:03 03/22/21 Funny. When I brought my white 90TT home, - Boosted1 19:14:23 03/22/21 Throw the UR pulley in the garbage. Worst mod I've ever done (n/m) - ZaXxon 08:34:09 03/23/21 I saw mostly positive comments on it, and with me nicking - Woodnutz (PA) 08:50:00 03/23/21 Vibration, belts slipping, PS pulley misaligned, zero actual - ZaXxon 08:55:20 03/23/21 I disagree. - Bernie (NoVA) 10:03:41 03/23/21 It's a trade-off - Zeus 11:20:29 03/23/21 Rubber has nothing to do w. dampening anything besides NVH - Bernie (NoVA) 13:23:05 03/23/21 It does have a lot to do with dampening harmonics when - MixManMash 13:56:34 03/23/21 Yeah, some engines need it - BlackholeZ 11:55:21 03/24/21 The V in NVH is vibration :) - Zeus 14:34:52 03/23/21 Yup, got an NA pulley from you years ago to address the - ZaXxon 11:52:16 03/23/21 I had issues throwing a belt with the ATI dampener too... - MixManMash 12:01:53 03/23/21 You've always provided me with good advice, so now I'll try - ZaXxon 13:35:13 03/23/21 How does the bearing in your tensioner feel? - Bernie (NoVA) 14:16:36 03/23/21 Good thought. I'll have to check that out. (n/m) - ZaXxon 15:55:09 03/23/21 Ding Ding! (n/m) - ConVerTT 20:53:15 03/23/21 Sounds like user error (n/m) - BlackholeZ 11:20:24 03/23/21 200K+ kms on my NA engine and 50K+ kms on my TT engine - itsa300zx 11:29:37 03/23/21 10 years on the ASP UD Pulley, no problems here. (n/m) - ZXRider 12:02:37 03/23/21 Why? I've run them for years - no issues.... (n/m) - ConVerTT 08:53:23 03/23/21 Same. (n/m) - Inzane 12:10:32 03/23/21 Congrats Woodnutz ...another z32 rite of passage behind you! - ConVerTT 08:38:06 03/23/21 Thanks! Yea, as much as I'd plan for a standalone setup - Woodnutz (PA) 09:10:09 03/23/21 Never say never. (n/m) - MixManMash 12:02:32 03/23/21 All true yup! (n/m) - ConVerTT 20:55:11 03/23/21 Must be 90s Nissan thing - IJUMPMAN 03:00:57 03/27/21 Many times it's just not being torqued to spec. (n/m) - CmyZ 15:22:54 03/28/21 Well, it’s torqued now ;) (n/m) - Woodnutz (PA) 23:20:39 03/29/21
Post a Followup	You cannot reply to this message because you are not logged in.