Subject	It was my first time installing larger piping...
Posted by	Zeus on May 29, 2020 at 11:02 AM
	This message has been viewed 147 times.
In Reply To	Aside from the trim work to fit the I/C's posted by DAYTONAZ on May 29, 2020 at 06:26 AM
Message	So without a frame of reference I'd say it went well? The SZ IC pipes that hug each side of the radiator are oval in that area to help with clearance. So that was a pleasant surprise. I expected to fight the inlet piping under the headlamps, but those slid right in. Just be sure to unbolt the AC condenser and lean it into the bay a little. That'll give you the necessary room to hook them in. It's the same thing for removing the stock ones. Also, keep all the clamps loose until everything is in place. You don't want to be fighting tightened clamps. Zeus
Follow Ups	Been busy with some work on the Z. Here's some pics. - Zeus 13:31:10 05/27/20 Nice, I like the engine sling. Did you fab it? - itsa300zx 14:10:05 05/27/20 ZFever makes them. Link inside. - Zeus 14:26:10 05/27/20 Very interesting, I've never seen it before. - Polishzx 15:43:35 05/27/20 Just more bolts spreading the load I suppose. - Barry (NJ) 16:30:24 05/27/20 no Amateur Z shirt for you... - vorpalZed 14:13:07 05/27/20 Plenum is standard wrinkle black powdercoat. - Zeus 14:28:40 05/27/20 nice, now get over and give spicyZ a hand :D (n/m) - vorpalZed 16:52:51 05/28/20 I've actually offered! - Zeus 11:08:50 05/29/20 Engine sling - ZXoltan 14:24:51 05/27/20 I've used it twice now and another local guy borrowed it - Zeus 14:30:33 05/27/20 Problem is... - BlackholeZ 20:24:43 05/27/20 Nice work! (n/m) - Inzane 15:23:11 05/27/20 Nicely done! - CameronSF 15:59:17 05/27/20 Changed intake valve cover gaskets. - Zeus 16:37:40 05/27/20 Sweet! (n/m) - Barry (NJ) 16:26:47 05/27/20 Nice work. I recently finished similar work. - Boosted1 17:49:19 05/27/20 Thanks! And I use imgur.com. Works well enough. (n/m) - Zeus 18:34:08 05/27/20 Nice! I've been doing similar - BlackholeZ 20:26:37 05/27/20 Bravo (n/m) - zgene4 22:35:36 05/27/20 Clean! Nicely done! I havent pulled the engine in 2 years.. - Stanky (BC) 23:51:38 05/27/20 Ha! Ya, I hope this isn't an annual event :P (n/m) - Zeus 07:45:47 05/28/20 Brings back memories. Nice work. - ZaXxon 05:56:25 05/28/20 Your signature picture reminds me that stock wheel look - bbug 07:58:58 05/28/20 They certainly do. - Zeus 12:52:09 05/28/20 Is there any prep work with the POR? Do you just paint it - SirpriZ 13:08:00 05/28/20 I took a wire wheel to it first to clean it up. - Zeus 13:23:04 05/28/20 Really helpful, thanks so much! (n/m) - SirpriZ 16:11:22 05/28/20 Nice work! (n/m) - moxie (SF) 14:49:49 05/28/20 Aside from the trim work to fit the I/C's - DAYTONAZ 06:26:12 05/29/20 It was my first time installing larger piping... - Zeus 11:02:56 05/29/20 Good job and hopefully you'll have it running soon - DAYTONAZ 14:53:09 05/30/20 That explains why the box with my MS Manis was so light ;) (n/m) - Aqualung 12:39:18 05/30/20 Re: That explains why the box with my MS Manis was so light ;) - Zeus 07:53:02 06/01/20
Post a Followup	You cannot reply to this message because you are not logged in.