Subject	Nice! I've been doing similar
Posted by	BlackholeZ on May 27, 2020 at 8:26 PM
	This message has been viewed 159 times.
In Reply To	Been busy with some work on the Z. Here's some pics. posted by Zeus on May 27, 2020 at 01:31 PM
Message	I pulled my motor because I've got a couple cylinders low. Well I found some serious corrosion damage in one and a couple bearings scored, so now I'm on the hunt for a new block and crank... Now I get a feeling for how the winter states feel. I'm not driving it so I might as well take it apart... -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Been busy with some work on the Z. Here's some pics. - Zeus 13:31:10 05/27/20 Nice, I like the engine sling. Did you fab it? - itsa300zx 14:10:05 05/27/20 ZFever makes them. Link inside. - Zeus 14:26:10 05/27/20 Very interesting, I've never seen it before. - Polishzx 15:43:35 05/27/20 Just more bolts spreading the load I suppose. - Barry (NJ) 16:30:24 05/27/20 no Amateur Z shirt for you... - vorpalZed 14:13:07 05/27/20 Plenum is standard wrinkle black powdercoat. - Zeus 14:28:40 05/27/20 nice, now get over and give spicyZ a hand :D (n/m) - vorpalZed 16:52:51 05/28/20 I've actually offered! - Zeus 11:08:50 05/29/20 Engine sling - ZXoltan 14:24:51 05/27/20 I've used it twice now and another local guy borrowed it - Zeus 14:30:33 05/27/20 Problem is... - BlackholeZ 20:24:43 05/27/20 Nice work! (n/m) - Inzane 15:23:11 05/27/20 Nicely done! - CameronSF 15:59:17 05/27/20 Changed intake valve cover gaskets. - Zeus 16:37:40 05/27/20 Sweet! (n/m) - Barry (NJ) 16:26:47 05/27/20 Nice work. I recently finished similar work. - Boosted1 17:49:19 05/27/20 Thanks! And I use imgur.com. Works well enough. (n/m) - Zeus 18:34:08 05/27/20 Nice! I've been doing similar - BlackholeZ 20:26:37 05/27/20 Bravo (n/m) - zgene4 22:35:36 05/27/20 Clean! Nicely done! I havent pulled the engine in 2 years.. - Stanky (BC) 23:51:38 05/27/20 Ha! Ya, I hope this isn't an annual event :P (n/m) - Zeus 07:45:47 05/28/20 Brings back memories. Nice work. - ZaXxon 05:56:25 05/28/20 Your signature picture reminds me that stock wheel look - bbug 07:58:58 05/28/20 They certainly do. - Zeus 12:52:09 05/28/20 Is there any prep work with the POR? Do you just paint it - SirpriZ 13:08:00 05/28/20 I took a wire wheel to it first to clean it up. - Zeus 13:23:04 05/28/20 Really helpful, thanks so much! (n/m) - SirpriZ 16:11:22 05/28/20 Nice work! (n/m) - moxie (SF) 14:49:49 05/28/20 Aside from the trim work to fit the I/C's - DAYTONAZ 06:26:12 05/29/20 It was my first time installing larger piping... - Zeus 11:02:56 05/29/20 Good job and hopefully you'll have it running soon - DAYTONAZ 14:53:09 05/30/20 That explains why the box with my MS Manis was so light ;) (n/m) - Aqualung 12:39:18 05/30/20 Re: That explains why the box with my MS Manis was so light ;) - Zeus 07:53:02 06/01/20
Post a Followup	You cannot reply to this message because you are not logged in.