Subject	Really with new style injectors the need for grinding is nil
Posted by	BlackholeZ on January 24, 2020 at 9:58 PM
	This message has been viewed 212 times.
In Reply To	Did you grind the plenum for injector #1 clearance? For >> posted by ZUL8TR on January 21, 2020 at 05:33 AM
Message	Though there is the necessary adjustment to clear the connector. -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Pictures of my 1991 Z32 TT Engine Build Project - 300ZXTCZ 22:51:02 01/19/20 Wow. That's show quality workmanship. Almost too pretty - Gordo LSZ Daytona 08:23:01 01/20/20 Re: Wow. That's show quality workmanship. Almost too pretty - 300ZXTCZ 10:07:03 01/20/20 Did you grind the plenum for injector #1 clearance? For >> - ZUL8TR 05:33:35 01/21/20 Re: Did you grind the plenum for injector #1 clearance? For >> - 300ZXTCZ 08:11:13 01/21/20 Really with new style injectors the need for grinding is nil - BlackholeZ 21:58:59 01/24/20 rotate the AN fitting elbow 90 deg to the left - vorpalZed 09:17:32 01/20/20 Can you swap the 45 ss line with the 90 ss line? - itsa300zx 11:03:14 01/20/20 Re: rotate the AN fitting elbow 90 deg to the left - 300ZXTCZ 12:34:58 01/20/20 Re: Pictures of my 1991 Z32 TT Engine Build Project - ni[x]it 10:00:09 01/20/20 Can you rotate it inboard, towards the pass side? (n/m) - ni[x]it 10:03:57 01/20/20 Re: Re: Pictures of my 1991 Z32 TT Engine Build Project - 300ZXTCZ 12:25:33 01/20/20 Please put timing covers on. (n/m) - Bernie (NoVA) 10:14:09 01/20/20 will have to keep them off for cam gear timing (n/m) - vorpalZed 10:40:57 01/20/20 That's no excuse to be missing the backing plates (n/m) - Bernie (NoVA) 19:07:26 01/20/20 agreed (n/m) - vorpalZed 19:18:26 01/20/20 Absolutely beautiful! Great job! (n/m) - The Hawk 12:05:13 01/20/20 Re: Absolutely beautiful! Great job! - 300ZXTCZ 12:28:05 01/20/20 Looks really nice. - Boosted1 16:51:03 01/20/20 Looked hard for a single spec of dirt to call you out on - Polishzx 21:01:35 01/20/20 Re: Looked hard for a single spec of dirt to call you out on - 300ZXTCZ 08:13:49 01/21/20 Ditch the silicone inlet and outlet couplers. - ZXRider 23:33:22 01/20/20 Re: Ditch the silicone inlet and outlet couplers. - 300ZXTCZ 08:18:56 01/21/20 Use the search function, or Google it - ZXRider 09:06:27 01/21/20 Re: Use the search function, or Google it - 300ZXTCZ 12:06:45 01/21/20 Sent you 300 degree instructions inEmail (n/m) - ZUL8TR 05:09:14 01/21/20 Re: Sent you 300 degree instructions inEmail - 300ZXTCZ 08:20:21 01/21/20 I angled that fitting outward a bit to clear the water pipe - Barry (NJ) 13:28:18 01/21/20 Wire wheel and clearcoat those throttle springs! ?? (n/m) - Ted (92TT) 23:01:59 01/21/20 Other than that, looks great :-) (n/m) - Ted (92TT) 23:05:13 01/21/20 Oooooo shinyyyyy (n/m) - Drk93TT 05:26:52 01/24/20 purdy, real purdy (n/m) - moxie (SF) 10:52:31 01/29/20
Post a Followup	You cannot reply to this message because you are not logged in.