Subject	Re: Pictures of my 1991 Z32 TT Engine Build Project
Posted by	ni[x]it on January 20, 2020 at 10:00 AM
	This message has been viewed 292 times.
In Reply To	Pictures of my 1991 Z32 TT Engine Build Project posted by 300ZXTCZ on January 19, 2020 at 10:51 PM
Message	Regarding the 300 degree fuel rail AN stainless fuel line 90 degree fitting. Currently, you can see that the water pipe is unable to connect where I'm pointing at the junction, as it is bumping against the fuel line. What is the suggested workaround for this? It looks like you used the Specialty Z braided kit. I made my own lines and used a 45 at that location. You might want to reach out to Greg/Seb and ask for their assistance. I'm sure this is explained in the 300 degree instructions or support forum, neither of which I currently have access to. It's not; the 300d kit is just the rails, caps, and installation hardware. I don't believe 300d ever offered a fuel line package with it. Do I gingerly bend/tilt the water pipe towards the passenger side? Help from anyone that has installed one of these fuel rails would be awsome!!! That's what I would do in your situation, however, chaffing on that pipe could be disastrous. Gorgeous build. I miss having the jewel of the motor on an engine stand. But I much prefer it in the car. :)
Follow Ups	Pictures of my 1991 Z32 TT Engine Build Project - 300ZXTCZ 22:51:02 01/19/20 Wow. That's show quality workmanship. Almost too pretty - Gordo LSZ Daytona 08:23:01 01/20/20 Re: Wow. That's show quality workmanship. Almost too pretty - 300ZXTCZ 10:07:03 01/20/20 Did you grind the plenum for injector #1 clearance? For >> - ZUL8TR 05:33:35 01/21/20 Re: Did you grind the plenum for injector #1 clearance? For >> - 300ZXTCZ 08:11:13 01/21/20 Really with new style injectors the need for grinding is nil - BlackholeZ 21:58:59 01/24/20 rotate the AN fitting elbow 90 deg to the left - vorpalZed 09:17:32 01/20/20 Can you swap the 45 ss line with the 90 ss line? - itsa300zx 11:03:14 01/20/20 Re: rotate the AN fitting elbow 90 deg to the left - 300ZXTCZ 12:34:58 01/20/20 Re: Pictures of my 1991 Z32 TT Engine Build Project - ni[x]it 10:00:09 01/20/20 Can you rotate it inboard, towards the pass side? (n/m) - ni[x]it 10:03:57 01/20/20 Re: Re: Pictures of my 1991 Z32 TT Engine Build Project - 300ZXTCZ 12:25:33 01/20/20 Please put timing covers on. (n/m) - Bernie (NoVA) 10:14:09 01/20/20 will have to keep them off for cam gear timing (n/m) - vorpalZed 10:40:57 01/20/20 That's no excuse to be missing the backing plates (n/m) - Bernie (NoVA) 19:07:26 01/20/20 agreed (n/m) - vorpalZed 19:18:26 01/20/20 Absolutely beautiful! Great job! (n/m) - The Hawk 12:05:13 01/20/20 Re: Absolutely beautiful! Great job! - 300ZXTCZ 12:28:05 01/20/20 Looks really nice. - Boosted1 16:51:03 01/20/20 Looked hard for a single spec of dirt to call you out on - Polishzx 21:01:35 01/20/20 Re: Looked hard for a single spec of dirt to call you out on - 300ZXTCZ 08:13:49 01/21/20 Ditch the silicone inlet and outlet couplers. - ZXRider 23:33:22 01/20/20 Re: Ditch the silicone inlet and outlet couplers. - 300ZXTCZ 08:18:56 01/21/20 Use the search function, or Google it - ZXRider 09:06:27 01/21/20 Re: Use the search function, or Google it - 300ZXTCZ 12:06:45 01/21/20 Sent you 300 degree instructions inEmail (n/m) - ZUL8TR 05:09:14 01/21/20 Re: Sent you 300 degree instructions inEmail - 300ZXTCZ 08:20:21 01/21/20 I angled that fitting outward a bit to clear the water pipe - Barry (NJ) 13:28:18 01/21/20 Wire wheel and clearcoat those throttle springs! ?? (n/m) - Ted (92TT) 23:01:59 01/21/20 Other than that, looks great :-) (n/m) - Ted (92TT) 23:05:13 01/21/20 Oooooo shinyyyyy (n/m) - Drk93TT 05:26:52 01/24/20 purdy, real purdy (n/m) - moxie (SF) 10:52:31 01/29/20
Post a Followup	You cannot reply to this message because you are not logged in.