Subject	rotate the AN fitting elbow 90 deg to the left
Posted by	vorpalZed on January 20, 2020 at 9:17 AM
	This message has been viewed 280 times.
In Reply To	Pictures of my 1991 Z32 TT Engine Build Project posted by 300ZXTCZ on January 19, 2020 at 10:51 PM
Message	you have the braided line going straight up and the water pipe hits the elbow. Rotate the AN elbow and the water pipe will fit better. If you have to bend the lower water pipe right slightly to allow better fitment, that's fine. 2nd thing: grind off the coating on your plenum on the ground points where the harness ground ring touches the plenum. You won't see it under the bolt head and you'll improve your grounding. Can't tell from the pics, but did your coater plug all the threaded holes on the plenum when they did the coating? I'd chase all the threads with a tap anyway just to make bolt installation easy. Last thing, the PCV tubes on the front of the valve covers... ensure they are glued in with a good hi-temp epoxy. I've seen them pop loose after being polished or coated and binding against the throttle linkage... usually under hard boost. Otherwise, spotless work!
Follow Ups	Pictures of my 1991 Z32 TT Engine Build Project - 300ZXTCZ 22:51:02 01/19/20 Wow. That's show quality workmanship. Almost too pretty - Gordo LSZ Daytona 08:23:01 01/20/20 Re: Wow. That's show quality workmanship. Almost too pretty - 300ZXTCZ 10:07:03 01/20/20 Did you grind the plenum for injector #1 clearance? For >> - ZUL8TR 05:33:35 01/21/20 Re: Did you grind the plenum for injector #1 clearance? For >> - 300ZXTCZ 08:11:13 01/21/20 Really with new style injectors the need for grinding is nil - BlackholeZ 21:58:59 01/24/20 rotate the AN fitting elbow 90 deg to the left - vorpalZed 09:17:32 01/20/20 Can you swap the 45 ss line with the 90 ss line? - itsa300zx 11:03:14 01/20/20 Re: rotate the AN fitting elbow 90 deg to the left - 300ZXTCZ 12:34:58 01/20/20 Re: Pictures of my 1991 Z32 TT Engine Build Project - ni[x]it 10:00:09 01/20/20 Can you rotate it inboard, towards the pass side? (n/m) - ni[x]it 10:03:57 01/20/20 Re: Re: Pictures of my 1991 Z32 TT Engine Build Project - 300ZXTCZ 12:25:33 01/20/20 Please put timing covers on. (n/m) - Bernie (NoVA) 10:14:09 01/20/20 will have to keep them off for cam gear timing (n/m) - vorpalZed 10:40:57 01/20/20 That's no excuse to be missing the backing plates (n/m) - Bernie (NoVA) 19:07:26 01/20/20 agreed (n/m) - vorpalZed 19:18:26 01/20/20 Absolutely beautiful! Great job! (n/m) - The Hawk 12:05:13 01/20/20 Re: Absolutely beautiful! Great job! - 300ZXTCZ 12:28:05 01/20/20 Looks really nice. - Boosted1 16:51:03 01/20/20 Looked hard for a single spec of dirt to call you out on - Polishzx 21:01:35 01/20/20 Re: Looked hard for a single spec of dirt to call you out on - 300ZXTCZ 08:13:49 01/21/20 Ditch the silicone inlet and outlet couplers. - ZXRider 23:33:22 01/20/20 Re: Ditch the silicone inlet and outlet couplers. - 300ZXTCZ 08:18:56 01/21/20 Use the search function, or Google it - ZXRider 09:06:27 01/21/20 Re: Use the search function, or Google it - 300ZXTCZ 12:06:45 01/21/20 Sent you 300 degree instructions inEmail (n/m) - ZUL8TR 05:09:14 01/21/20 Re: Sent you 300 degree instructions inEmail - 300ZXTCZ 08:20:21 01/21/20 I angled that fitting outward a bit to clear the water pipe - Barry (NJ) 13:28:18 01/21/20 Wire wheel and clearcoat those throttle springs! ?? (n/m) - Ted (92TT) 23:01:59 01/21/20 Other than that, looks great :-) (n/m) - Ted (92TT) 23:05:13 01/21/20 Oooooo shinyyyyy (n/m) - Drk93TT 05:26:52 01/24/20 purdy, real purdy (n/m) - moxie (SF) 10:52:31 01/29/20
Post a Followup	You cannot reply to this message because you are not logged in.