Subject	No I set the idle screw to hold the idle @ 925ish (n/m)
Posted by	Bernie (NoVA) on December 19, 2019 at 3:46 PM
	This message has been viewed 249 times.
In Reply To	How do you disabled the ECU input to set base timing? posted by moxie (SF) on December 19, 2019 at 08:57 AM
Message
Follow Ups	The saga continues, but getting close *I think* - moxie (SF) 01:38:34 12/15/19 Re: The saga continues, but getting close *I think* - itsa300zx 09:27:59 12/15/19 Re: Re: The saga continues, but getting close *I think* - moxie (SF) 10:37:26 12/15/19 Check your TPS Volts Setting/Switch Setting - Cjw3 15:40:45 12/15/19 Go through the entire idle set routine - platinumist 21:19:04 12/15/19 I did, everything is now set up correctly, total pita - moxie (SF) 22:47:43 12/15/19 2. Normal on 16bit ecu. - Bernie (NoVA) 10:25:11 12/16/19 If that's the case, then I think everything is okay. - moxie (SF) 12:59:03 12/16/19 The 16bit ecu has more resolution vs the 8bit, plus no AIV - Bernie (NoVA) 20:43:49 12/17/19 How do you disabled the ECU input to set base timing? - moxie (SF) 08:57:41 12/19/19 Use the Base Idle setting in Datascan - vorpalZed 09:43:57 12/19/19 awesome, thanks, very helpful. Datascan is an awesome tool - moxie (SF) 16:14:54 12/19/19 I like the + 50 RPM spec for Canada... keeps us warm in the - vorpalZed 16:48:35 12/19/19 good tip (n/m) - moxie (SF) 17:16:43 12/19/19 No I set the idle screw to hold the idle @ 925ish (n/m) - Bernie (NoVA) 15:46:44 12/19/19 awesome, thanks again! Very helpful. I'm surprised this is - moxie (SF) 16:15:38 12/19/19 Lesson of the day: 8 more bits make it twitchy. (n/m) - MixManMash 13:32:44 12/16/19 One more follow up for the record in the hopes this whole - moxie (SF) 13:42:58 12/16/19 congrats! You've earned your Amateur Z banner: - vorpalZed 14:30:02 12/16/19 lol. Yeah. I definitely earned that. Hahah (n/m) - moxie (SF) 17:57:22 12/16/19 Nice! (n/m) - Barry (NJ) 14:39:40 12/16/19 nice.....you just learned more than 99% of Z owners (n/m) - LJZTT 14:55:19 12/16/19 Good job. (n/m) - Boosted1 16:43:29 12/16/19 Yep. I have seen that issue first hand. - MixManMash 18:28:45 12/16/19 I thought using the PTU loop was standard - ZXRider 08:58:24 12/17/19 I haven't had good luck with the PTU loop either. (n/m) - MixManMash 18:55:34 12/17/19 Same, only consistent reading I can get is using - Tanley (ATL) 20:01:45 12/17/19 Guilty. (n/m) - ConVerTT 15:18:16 12/17/19 now I need to recheck my timing lol - platinumist 19:05:43 12/16/19 my harbor freight one does - moxie (SF) 00:49:36 12/17/19 I believe it lets you dial in advance or retard amount... - Ted (92TT) 01:16:52 12/17/19 I set the advance on mine to 15, so that when timing is - MixManMash 07:06:55 12/17/19 The advance/retard function also help check where timing is. - MixManMash 07:34:49 12/17/19 Ahh. That makes sense. (n/m) - moxie (SF) 10:43:52 12/17/19 Great job seeing it through. You're an inspiration - spicyZ 08:18:27 12/17/19 Nice. (n/m) - Bernie (NoVA) 20:46:34 12/17/19
Post a Followup	You cannot reply to this message because you are not logged in.