Subject	Nice. Are the ends bead rolled?
Posted by	Barry (NJ) on October 07, 2019 at 10:33 AM
	This message has been viewed 202 times.
In Reply To	Product release: Pipe kits and Intercoolers.... posted by Greg D. (Specialty-Z) on September 30, 2019 at 04:23 PM
Message	That is a slight issue with the original design. The bead rolling adds strength to the ends, to help prevent buckling when clamping the silicone sections to the AL sections.
Follow Ups	Product release: Pipe kits and Intercoolers.... - Greg D. (Specialty-Z) 16:23:20 09/30/19 NICE. (n/m) - Bernie (NoVA) 16:32:44 09/30/19 Love to see new SZ products. (n/m) - Polish 16:35:48 09/30/19 Damn it, wish these were out 3 months ago. Nice pipes;) (n/m) - itsa300zx 17:19:46 09/30/19 yes! This is the next upgrade (n/m) - Z-line 18:07:15 09/30/19 Nice!! So you're saying vband manifolds next is next?! - Stanky (BC) 18:51:22 09/30/19 This. (n/m) - MixManMash 19:16:42 09/30/19 Two thumbs up! Any plans for SZ exhaust manifolds? (n/m) - Tanley (ATL) 18:52:58 09/30/19 Going in to SZ in December for install on all 3! (n/m) - RonZ300 (Socal) 18:59:11 09/30/19 Sweet! (n/m) - komplexZTT 19:31:54 09/30/19 Great stuff! And thank you! (n/m) - ConVerTT 19:57:18 09/30/19 so it wasn't just idle chatter @ Dynopalo0za this year... - vorpalZed 20:11:23 09/30/19 It was time... Thank you for your dedication to the Z32s. (n/m) - KevinsFairlady 20:50:18 09/30/19 Awesome! - RobZ32 21:38:37 09/30/19 Excellent! (n/m) - Inzane 22:30:40 09/30/19 Can these be installed with the engine in the car? (n/m) - moxie (SF) 23:11:27 09/30/19 I don't see why not. Inlet piping would be difficult, - MixManMash 23:30:05 09/30/19 It all can be installed with the engine in the car.... - Greg D. (Specialty-Z) 11:47:52 10/01/19 What's the trick to getting the turbo inlet pipe to seal - MixManMash 15:33:18 10/01/19 It will seal in any position, the slot is for orientation - Greg D. (Specialty-Z) 15:57:46 10/01/19 Awesome and quality products as usual ! (n/m) - Drk93TT 06:14:25 10/01/19 Fantastic! (n/m) - Zeus 07:00:56 10/01/19 Do you have the tapered pipes out of the turbos? - Woody75 (Denver) 07:54:06 10/01/19 IIRC, those pipes became a standard with the Ash IC piping, - MixManMash 09:59:17 10/01/19 Yes, they are included in the set. Not sold separately:( (n/m) - itsa300zx 11:12:12 10/01/19 Those pipes originated and were designed here.... - Greg D. (Specialty-Z) 11:43:57 10/01/19 Finally I always felt bad contributing to ASH and his - DarkZide 08:06:23 10/01/19 Where's.... ummm.... who? (n/m) - ZXoltan 17:24:01 10/01/19 Looks great. Option for the intake kit for no PCVs? - Red Hawk (CO) 09:28:35 10/01/19 We are producing them in bulk with the PCV.... - Greg D. (Specialty-Z) 11:50:26 10/01/19 I 100% approve of this message. SZ for the win! (n/m) - Gennosuke 10:14:34 10/01/19 THANK YOU ALL for the positive feedback and support!! (n/m) - Greg D. (Specialty-Z) 11:51:58 10/01/19 Awesome. SZ FTW. (n/m) - CameronSF 11:58:19 10/01/19 What about intercooler duct application? (n/m) - ZXoltan 11:59:21 10/01/19 The intercoolers are set up with.... - Greg D. (Specialty-Z) 12:43:22 10/01/19 the ducts are small enough to 3D print. - Spectrum (WI) 19:50:39 10/07/19 Well that's pretty awesome! (n/m) - Musashi Sword 13:10:53 10/01/19 You guys absolutely rock! This is exactly what I've been waiting for. (n/m) - Aqualung 14:08:49 10/01/19 Great news, Thanks SZ (n/m) - BooZtid 14:50:58 10/01/19 Nice. Will you be offering any other finish options? - Boosted1 15:03:11 10/01/19 Currently we have polished or micro wrinkle black powercoat - Greg D. (Specialty-Z) 15:47:50 10/01/19 Good Stuff!!! (n/m) - Mr.Stacy 15:26:36 10/01/19 Yessssss.... - LitlElvis 16:25:58 10/01/19 boy, a set of v-band exhaust manifolds suuuuurrreee - vorpalZed 17:33:11 10/01/19 With external wastegates plumbed back into the downpipe... - MixManMash 19:55:28 10/01/19 Right on! Looks great! - RoidRage76 00:35:33 10/02/19 This is great news! - WhiTTe Z 09:13:13 10/02/19 Well done (n/m) - Ghoztt 15:27:53 10/02/19 Awesome, in for one! (n/m) - BoneZ (MD) 20:55:48 10/02/19 Nice, mine should be here Friday. Just in time for weekend - 300MPH 06:54:36 10/03/19 About time someone steps up! - platinumist 10:55:15 10/03/19 One day.... - Dallas DamonZ 16:07:36 10/03/19 Do you have an option to accommodate - RZturbo 10:12:32 10/04/19 For blow-off valve flanges...to clarify (n/m) - RZturbo 10:16:16 10/04/19 Have you dyno tested the new set up and if so - DAYTONAZ 06:17:10 10/05/19 Nice. Are the ends bead rolled? - Barry (NJ) 10:33:40 10/07/19 Awesome work! (n/m) - Mike (NoVA) 11:46:01 10/09/19
Post a Followup	You cannot reply to this message because you are not logged in.