Subject	Have you dyno tested the new set up and if so
Posted by	DAYTONAZ on October 05, 2019 at 6:17 AM
	This message has been viewed 209 times.
In Reply To	Product release: Pipe kits and Intercoolers.... posted by Greg D. (Specialty-Z) on September 30, 2019 at 04:23 PM
Message	What are the numbers over stock pipes with upgraded I/C’s? And are they made here in the USA? Thanks
Follow Ups	Product release: Pipe kits and Intercoolers.... - Greg D. (Specialty-Z) 16:23:20 09/30/19 NICE. (n/m) - Bernie (NoVA) 16:32:44 09/30/19 Love to see new SZ products. (n/m) - Polish 16:35:48 09/30/19 Damn it, wish these were out 3 months ago. Nice pipes;) (n/m) - itsa300zx 17:19:46 09/30/19 yes! This is the next upgrade (n/m) - Z-line 18:07:15 09/30/19 Nice!! So you're saying vband manifolds next is next?! - Stanky (BC) 18:51:22 09/30/19 This. (n/m) - MixManMash 19:16:42 09/30/19 Two thumbs up! Any plans for SZ exhaust manifolds? (n/m) - Tanley (ATL) 18:52:58 09/30/19 Going in to SZ in December for install on all 3! (n/m) - RonZ300 (Socal) 18:59:11 09/30/19 Sweet! (n/m) - komplexZTT 19:31:54 09/30/19 Great stuff! And thank you! (n/m) - ConVerTT 19:57:18 09/30/19 so it wasn't just idle chatter @ Dynopalo0za this year... - vorpalZed 20:11:23 09/30/19 It was time... Thank you for your dedication to the Z32s. (n/m) - KevinsFairlady 20:50:18 09/30/19 Awesome! - RobZ32 21:38:37 09/30/19 Excellent! (n/m) - Inzane 22:30:40 09/30/19 Can these be installed with the engine in the car? (n/m) - moxie (SF) 23:11:27 09/30/19 I don't see why not. Inlet piping would be difficult, - MixManMash 23:30:05 09/30/19 It all can be installed with the engine in the car.... - Greg D. (Specialty-Z) 11:47:52 10/01/19 What's the trick to getting the turbo inlet pipe to seal - MixManMash 15:33:18 10/01/19 It will seal in any position, the slot is for orientation - Greg D. (Specialty-Z) 15:57:46 10/01/19 Awesome and quality products as usual ! (n/m) - Drk93TT 06:14:25 10/01/19 Fantastic! (n/m) - Zeus 07:00:56 10/01/19 Do you have the tapered pipes out of the turbos? - Woody75 (Denver) 07:54:06 10/01/19 IIRC, those pipes became a standard with the Ash IC piping, - MixManMash 09:59:17 10/01/19 Yes, they are included in the set. Not sold separately:( (n/m) - itsa300zx 11:12:12 10/01/19 Those pipes originated and were designed here.... - Greg D. (Specialty-Z) 11:43:57 10/01/19 Finally I always felt bad contributing to ASH and his - DarkZide 08:06:23 10/01/19 Where's.... ummm.... who? (n/m) - ZXoltan 17:24:01 10/01/19 Looks great. Option for the intake kit for no PCVs? - Red Hawk (CO) 09:28:35 10/01/19 We are producing them in bulk with the PCV.... - Greg D. (Specialty-Z) 11:50:26 10/01/19 I 100% approve of this message. SZ for the win! (n/m) - Gennosuke 10:14:34 10/01/19 THANK YOU ALL for the positive feedback and support!! (n/m) - Greg D. (Specialty-Z) 11:51:58 10/01/19 Awesome. SZ FTW. (n/m) - CameronSF 11:58:19 10/01/19 What about intercooler duct application? (n/m) - ZXoltan 11:59:21 10/01/19 The intercoolers are set up with.... - Greg D. (Specialty-Z) 12:43:22 10/01/19 the ducts are small enough to 3D print. - Spectrum (WI) 19:50:39 10/07/19 Well that's pretty awesome! (n/m) - Musashi Sword 13:10:53 10/01/19 You guys absolutely rock! This is exactly what I've been waiting for. (n/m) - Aqualung 14:08:49 10/01/19 Great news, Thanks SZ (n/m) - BooZtid 14:50:58 10/01/19 Nice. Will you be offering any other finish options? - Boosted1 15:03:11 10/01/19 Currently we have polished or micro wrinkle black powercoat - Greg D. (Specialty-Z) 15:47:50 10/01/19 Good Stuff!!! (n/m) - Mr.Stacy 15:26:36 10/01/19 Yessssss.... - LitlElvis 16:25:58 10/01/19 boy, a set of v-band exhaust manifolds suuuuurrreee - vorpalZed 17:33:11 10/01/19 With external wastegates plumbed back into the downpipe... - MixManMash 19:55:28 10/01/19 Right on! Looks great! - RoidRage76 00:35:33 10/02/19 This is great news! - WhiTTe Z 09:13:13 10/02/19 Well done (n/m) - Ghoztt 15:27:53 10/02/19 Awesome, in for one! (n/m) - BoneZ (MD) 20:55:48 10/02/19 Nice, mine should be here Friday. Just in time for weekend - 300MPH 06:54:36 10/03/19 About time someone steps up! - platinumist 10:55:15 10/03/19 One day.... - Dallas DamonZ 16:07:36 10/03/19 Do you have an option to accommodate - RZturbo 10:12:32 10/04/19 For blow-off valve flanges...to clarify (n/m) - RZturbo 10:16:16 10/04/19 Have you dyno tested the new set up and if so - DAYTONAZ 06:17:10 10/05/19 Nice. Are the ends bead rolled? - Barry (NJ) 10:33:40 10/07/19 Awesome work! (n/m) - Mike (NoVA) 11:46:01 10/09/19
Post a Followup	You cannot reply to this message because you are not logged in.