Subject	Switching to 2.5 intercoolers and piping
Posted by	Boostjuice on June 23, 2019 at 9:27 AM
	This message has been viewed 675 times.
Message	I am just running stock intercooler piping and the z1 2.0in intercoolers, am I going to make any gains by swapping to the 2.5 setup? Or just be able to run a lower boost duty cycle and still make the same power more reliably. I’m trying to see if I can squeeze any more power out of these things Jwt530bb/e85
Follow Ups	Switching to 2.5 intercoolers and piping - Boostjuice 09:27:36 06/23/19 You'll get to 575ish HP with 530BBs and bigger ICs and - MixManMash 11:03:35 06/23/19 That’s a decent gain. Has ash disappeared again? - Boostjuice 13:43:44 06/23/19 I'm pretty sure he has as usual. I have seen the Z1 - MixManMash 13:56:26 06/23/19 Yeah the piping will make a difference - Stanky (BC) 13:59:11 06/23/19 I already have the ashspec inlet piping - Boostjuice 14:13:51 06/23/19 I have some interesting dynos, that I can't post because - SirpriZ 16:24:22 06/23/19 PS These numbers are on conventional race fuel (Q-16). The - SirpriZ 16:32:13 06/23/19 I can text you a pic of my dynos of before and after the - SirpriZ 17:59:20 06/24/19 unless you have a set of piping AND intercoolers already - LJZTT 15:53:47 06/25/19 Did you post the cam dyno (stock vs 500)? - ZXoltan 15:42:11 06/23/19 Cant seem to find it. Maybe Mixman or Vorpalz? - Stanky (BC) 23:54:45 06/23/19 Here you go. From 2017. - MixManMash 07:58:51 06/24/19 looks like a single set up at 3 different boost levels (n/m) - LJZTT 11:39:55 06/26/19 It is; with stock cams. Above graph 575ish HP w/500cams (n/m) - itsa300zx 12:00:43 06/26/19 was hoping to see how the curve was affected.... - LJZTT 18:20:41 06/26/19 Either Stanky or vorpalz should have the run files. (n/m) - MixManMash 20:44:22 06/26/19 Just compare the graph he posted above to the one now - Stanky (BC) 00:06:11 06/27/19 derp, I missed it (n/m) - LJZTT 16:10:08 07/02/19 Thus improving reliability? - ZXoltan 11:22:34 06/24/19 Not necessarily. It just means that things are running so - MixManMash 13:43:39 06/24/19 I like less heat (n/m) - LJZTT 18:52:44 06/26/19 Great dyno numbers. Did you do any headwork along the - SirpriZ 17:00:05 06/23/19 The only headwork I had done was 5angle valve job - Boostjuice 17:28:50 06/23/19 That "only" valve job is one of the better modifications - SirpriZ 20:19:16 06/23/19 Maybe I'm splitting hairs, but the average Sport 530 build - SirpriZ 20:34:50 06/23/19 When stanky didn’t have cams, just exhaust cam gears - Boostjuice 21:02:48 06/23/19
Post a Followup	You cannot reply to this message because you are not logged in.