Subject	Re: But only one trigger point on the wheel is assigned to a
Posted by	MagicMike on March 13, 2019 at 5:23 AM
	This message has been viewed 444 times.
In Reply To	But only one trigger point on the wheel is assigned to a posted by LitlElvis on March 13, 2019 at 01:52 AM
Message	I cant speak for how all ecus run the calcs, but for link g4+, they update engine speed at every tooth seen. Under heavy accel we can expect some pretty decent engine speed changes during engine cycles. Most of the people going towards crank triggers are on the higher hp end of scale and expect greater rate of change in engine speed. Anyway, I went with the 36-2 over the 12 each to their own. There's plenty more knowledgeable people on the subject than me.
Follow Ups	BDE crank trigger market research > - LitlElvis 01:32:18 03/12/19 Re: BDE crank trigger market research > - MagicMike 01:46:55 03/12/19 Both... trigger wheel location dictates the sensor location - LitlElvis 02:20:07 03/12/19 Re: Both... trigger wheel location dictates the sensor location - JSD-ZX 06:57:57 03/12/19 Re: Both... trigger wheel location dictates the sensor location - MagicMike 19:15:44 03/12/19 Option 2 would be my personal choice. I'm also... - SlicktopZ 01:55:00 03/12/19 Option 1 - JaffaUK 04:43:58 03/12/19 Option 1 (n/m) - MixManMash 07:38:47 03/12/19 Option #2 - induetime 13:26:33 03/12/19 BOTH - EVLTWINZ 14:11:32 03/12/19 True. (n/m) - MixManMash 19:24:24 03/12/19 Not sure about your dry sump setup, send me a front pic - LitlElvis 14:30:22 03/12/19 Re: BDE crank trigger market research > - ouikikazz 15:17:14 03/12/19 Or options for teeth. (n/m) - MixManMash 19:24:51 03/12/19 More than 12 trigger points for increased resolution? - LitlElvis 20:08:17 03/12/19 Re: More than 12 trigger points for increased resolution? - MagicMike 21:03:44 03/12/19 But only one trigger point on the wheel is assigned to a - LitlElvis 01:52:08 03/13/19 Re: But only one trigger point on the wheel is assigned to a - MagicMike 05:23:30 03/13/19 Ok, I put some work into this and here's what I found - LitlElvis 02:03:16 03/14/19 Re: Ok, I put some work into this and here's what I found - ouikikazz 06:38:20 03/14/19 Agreed. (n/m) - MixManMash 07:35:16 03/14/19 Re: Re: But only one trigger point on the wheel is assigned to a - MagicMike 06:05:34 03/14/19 The sensors I'm looking at are rated to 20kHz, which - LitlElvis 10:52:38 03/14/19 Any idea what the data rates/freq limit on common - J-Mart 16:35:30 03/14/19 Thing is that many low/mid level ecus. .. - kickerzx 07:36:29 03/15/19 True. The Haltech Platinum Pro PNP for the Z32 only - MixManMash 16:58:48 03/15/19 Option 2. Ease of installation, troubleshooting and maint. - PiotrC70 19:15:48 03/12/19 Lol. So true on those coolant pipes. - MixManMash 19:25:41 03/12/19 I would be ok with either. - Boosted1 20:49:10 03/12/19 Is it..... - Madhatter10-6 22:46:09 03/12/19 more parts = more initial investment cost - LitlElvis 01:51:22 03/13/19 Makes sense.... - Madhatter10-6 08:51:56 03/13/19 Are you making a Z32 product? Thanks for the xometry lead - LitlElvis 10:58:11 03/14/19 Not yet...this one will be for the MKIV Supra - Madhatter10-6 10:21:35 03/15/19 Re: BDE crank trigger market research > - Cjw3 09:32:46 03/13/19 Option 2 (n/m) - nonstopna 10:21:25 03/13/19 option 2, as i already have an ATI race damper. (n/m) - slayer fan 10:59:08 03/13/19 It looks like option 2 is a clear 2:1 winner - thank you all - LitlElvis 02:25:05 03/14/19 el dos (n/m) - LJZTT 19:07:40 03/15/19 Option 2 (n/m) - RobZ32 10:23:42 03/16/19
Post a Followup	You cannot reply to this message because you are not logged in.