Subject	Here are a few of the arms I built for it...
Posted by	Bernie (NoVA) on January 29, 2019 at 9:56 PM
	This message has been viewed 701 times.
In Reply To	Final pics of the post-swap underside posted by Gordo NA2LS Daytona on January 29, 2019 at 09:29 AM
Message	Rear arms - new Nismo bushings x4, Japanese rear ball joints x2 Rear toe / traction / upper arms Nissan bushings x6 Front Lower arms - Nismo bushing x2, NOK Japan ball joint x2 Bernie Bilski berniebilski@cox.net President of Z-Car Club of Northern Virginia 1995 Nissan 300ZX TwinTurbo in Cobalt Green 1997 Nissan 240SX SE in Ultra Red 2006 Nissan Frontier SE in Ultra Black
Follow Ups	Final pics of the post-swap underside - Gordo NA2LS Daytona 09:29:32 01/29/19 I dig the custom tension rods! - ZXRider 09:54:38 01/29/19 Wanted rubber bushings, but needed an adjustable length. - Gordo NA2LS Daytona 10:02:51 01/29/19 They are off the shelf? Who sells them? (n/m) - ZXRider 10:14:24 01/29/19 Specialty Products Company (SPC) 67720 -Front Caster Rod - Gordo NA2LS Daytona 10:23:35 01/29/19 I'm running these also. I was a bit disappointed by how - black300zx 11:24:32 01/29/19 Did you tighten the bushing with full weight of the front - Gordo NA2LS Daytona 12:45:15 01/29/19 Quite honestly, I forget. It was several years ago. (n/m) - black300zx 14:19:41 01/29/19 Looks great - your rear subframe studs are missing the cups - Bernie (NoVA) 17:21:00 01/29/19 Good eye. I found them after I took the pics... - Gordo NA2LS Daytona 18:23:23 01/29/19 Glad to. (n/m) - Bernie (NoVA) 18:26:16 01/29/19 I've seen the SPC bushings fail after a year or so but I - Bernie (NoVA) 20:29:41 01/30/19 Have the SPC also. No problems... - ElectroZ 19:43:10 02/01/19 Their failure point is their bushings so you've basically - Bernie (NoVA) 14:56:47 02/03/19 Your car is turning out awesome. (n/m) - Musashi Sword 10:19:16 01/29/19 That's very impressive. Well done! (n/m) - Zeus 10:54:33 01/29/19 Awesome clutch pull pics, lol. Practical question... - Ted (92TT) 11:06:38 01/29/19 Initial bottomside cleaning was in the garage, on the lift> - Gordo NA2LS Daytona 11:54:50 01/29/19 Nice (note to slackers, skip straight to the last line) - Ted (92TT) 18:47:34 01/29/19 Wow! Very nice work. (n/m) - Boosted1 20:46:20 01/29/19 Beautiful work !!! (n/m) - JDELUNA 21:09:20 01/29/19 Gorgeous (n/m) - moxie (SF) 21:56:30 01/29/19 Here are a few of the arms I built for it... - Bernie (NoVA) 21:56:34 01/29/19 Sweet (n/m) - Zeus 14:57:08 01/30/19 Yes Please!!! (n/m) - FrozTTy 12:41:48 01/31/19 Anyone who gets these will not be disappointed. (n/m) - Gordo NA2LS Daytona 20:42:50 01/31/19 off topic, but now that you have taken on some - LJZTT 16:01:35 01/30/19 For a garage space not totally dedicated to housing a lift, - Gordo NA2LS Daytona 16:36:18 01/30/19 How high does your ceiling need to be to accommodate for it? (n/m) - ZXRider 22:45:37 01/30/19 The max lift height is 72" so 12' is recommended. - Gordo NA2LS Daytona 09:11:15 01/31/19 Very nice (n/m) - DAYTONAZ 06:03:02 02/01/19 Very Impressive. In time, you'll need a brake upgrade - MikeD (Philly) 07:58:50 02/01/19
Post a Followup	You cannot reply to this message because you are not logged in.