TwinTurbo.NET: Nissan 300ZX forum - 5/16" Aluminum line.
Subject
5/16" Aluminum line.
Posted by
Woody75 (Denver)
on June 29, 2018 at 12:40 PM
This message has been viewed
318
times.
In Reply To
Aluminum lines I assume? Do you flare the ends
posted by ZXoltan
on June 29, 2018 at 08:39 AM
Message
Can be found at Summit Racing, etc. I use the Eastwood flare tool. Expensive but I use it a lot. I also do hard lines for wastegate lines (1/4") and PCV (3/8") so I've got my moneys worth out of it.
Follow Ups
Maintenance with lower plenum off...
-
s_zero99
03:52:24 06/29/18
Can't really "delete" those water lines
-
Barry (NJ)
06:08:11 06/29/18
Those 2 feed the turbos.
-
Bernie (NoVA)
06:44:00 06/29/18
Aluminum lines I assume? Do you flare the ends
-
ZXoltan
08:39:33 06/29/18
yes I flare the ends. (n/m)
-
Bernie (NoVA)
10:40:41 06/29/18
I do the same with stainless tubing, flared ends (n/m)
-
-Grimm-
10:52:43 06/29/18
5/16" Aluminum line. -
Woody75 (Denver)
12:40:16 06/29/18
A 39 or 45 deg Flare tool or a reamer/ bead tool? (n/m)
-
Zbullet
16:34:21 06/29/18
Bead is actually what I was thinking of, but this seems
-
ZXoltan
12:46:09 07/01/18
I used a brake flaring tool
-
-Grimm-
13:49:37 07/01/18
Like this one?
-
ZXoltan
14:00:34 07/01/18
I used a basic kit like this for years
-
Woody75 (Denver)
08:40:30 07/03/18
Yeah pretty much like that. Think I bought it from Autozone (n/m)
-
-Grimm-
09:41:47 07/03/18
I use this Eastwood one
-
Woody75 (Denver)
08:12:20 07/02/18
thanks Tim. Does that form a bead or only flare the end?
-
ZXoltan
12:02:58 07/02/18
Does both as far as I know. I only use the bead/bulb setting (n/m)
-
Woody75 (Denver)
08:03:41 07/03/18
Cool.... thanks guys. I'll prob buy a cheap tool and
-
ZXoltan
10:04:22 07/03/18
Re: Maintenance with lower plenum off...
-
JRFITZ
08:02:29 06/29/18
check your knock sensor for corrosion and replace.
-
PiotrC70
14:49:47 06/29/18
true (n/m)
-
Bernie (NoVA)
08:23:50 07/01/18
Re: Maintenance with lower plenum off...
-
s_zero99
17:18:02 07/01/18
Bernie, do you offer the formed tubes as a service?
-
ZXoltan
12:09:08 07/02/18
Cheap flaring tool from Harbor Freight will work as well. (n/m)
-
Woody75 (Denver)
08:05:13 07/03/18
Agreed (n/m)
-
Bernie (NoVA)
23:29:20 07/03/18
Lifters should feel solid when you press on them
-
-Grimm-
09:43:21 07/03/18
I rerouted my DS turbo hardlines
-
Zbruh92
23:08:22 07/06/18
Post a
Followup
You cannot reply to this message because you are not
logged in
.