Subject	I agree.
Posted by	GrecV2 on May 08, 2018 at 9:14 AM
	This message has been viewed 257 times.
In Reply To	If you've got enough torque to pull it off, no. posted by Gordo NA2LS Daytona on May 07, 2018 at 09:29 PM
Message	I ran 3:23s in my Challenger, and although it wasn't a beast off the line, she got up just fine... and kept me from running crazy RPMs with that 4-speed on the freeway. Of course, it's got a 440 w/ about 500lbs of torque Former Stage V addict... off the wagon.
Follow Ups	Would 3.357 be too tall a final drive for a modded TT? - Barry (NJ) 19:36:43 05/07/18 i think it just depends how modded. - jmw300zx 20:43:57 05/07/18 isn't Z33 something like 3.29? (n/m) - LJZTT 21:21:10 05/07/18 According to my searching Z33 R200 came in 3 flavors... - Barry (NJ) 21:28:42 05/07/18 But the trans ratios in first thru third are also very low - Gordo NA2LS Daytona 06:13:07 05/08/18 this ia a good point, I've never really looked into the - LJZTT 10:55:13 05/08/18 If you've got enough torque to pull it off, no. - Gordo NA2LS Daytona 21:29:05 05/07/18 torque or HP? (n/m) - ForceFedTT 21:42:26 05/07/18 I agree. - GrecV2 09:14:58 05/08/18 Your 440 is a completely different animal. - not4resaleZ 10:05:04 05/08/18 I get that the curves are different, but I would still think - GrecV2 13:19:29 05/08/18 It could be like a N/A with low compression - not4resaleZ 15:22:27 05/08/18 My car with stock auto turbos probably hits 200 ft lbs - not4resaleZ 16:01:23 05/08/18 Re: If you've got enough torque to pull it off, no. - sparkie 19:10:02 05/15/18 You & Gordo can start an old man club, maybe get a bus pass - Bernie (NoVA) 21:38:32 05/07/18 Meh, shredding tires from a roll in 2nd and... - Barry (NJ) 21:49:05 05/07/18 Do a TT subframe w. a 3.62... - Bernie (NoVA) 22:55:26 05/07/18 Newton. Lol. Nice. (n/m) - GrecV2 09:12:10 05/08/18 An R200V from 90-96 Q45 w/ 3.54 is a direct bolt in IF>> - Gordo NA2LS Daytona 11:39:08 05/08/18 I'm familiar w. dealing w. diff design cross fitment. - Bernie (NoVA) 21:47:00 05/08/18 You'll think twice when I cruise by you doing 95 and - Gordo NA2LS Daytona 22:31:32 05/07/18 No I won't. (n/m) - Bernie (NoVA) 22:52:27 05/07/18 [Looks down at tach] Ouch - BlackholeZ 22:59:54 05/07/18 Re: [Looks down at tach] Ouch - cc 00:35:27 05/08/18 What modifications did you need to use the Z33 tranny? - ZXoltan 07:45:00 05/08/18 They are strong. Early versions of the gearbox had synchro - MixManMash 07:53:22 05/08/18 oK... so how do we make 'em fit our cars? (n/m) - ZXoltan 18:04:26 05/08/18 Re: What modifications did you need to use the Z33 tranny? - cc 20:31:46 05/08/18 Did you modify the gearing? - BlackholeZ 21:02:17 05/09/18 Re: Did you modify the gearing? - cc 21:23:32 05/09/18 It does (n/m) - Bernie (NoVA) 01:44:15 05/10/18 The armada has a R230 2.94s. - Zluster 22:30:15 05/07/18 That may be a bit too tall ;-) (n/m) - Barry (NJ) 22:34:01 05/07/18 The remedy lies in the transmission, not the rear axle. - Gordo NA2LS Daytona 06:16:44 05/08/18 This. (n/m) - MixManMash 07:54:58 05/08/18 The T56 really does look like the answer. - Barry (NJ) 08:54:35 05/08/18 I think what works in a fairly large displacement v8 - not4resaleZ 10:19:24 05/08/18 Re: I think what works in a fairly large displacement v8 - cc 21:11:32 05/08/18 It depends on what you want. My 815hp Z32 will absolutely - MixManMash 21:30:54 05/08/18 especially with so many modded TT's equipped with - LJZTT 11:03:31 05/09/18 yep, folks forget that this car's transmission was designed - LJZTT 21:24:29 05/08/18 Maybe some forgot, but the Autobahn had no speed limits, - not4resaleZ 09:31:08 05/09/18 the likelihood of losing control is dramatically higher at - LJZTT 11:01:23 05/09/18 ...and as someone who may have more autobahn miles - LJZTT 11:21:38 05/09/18 I understand the desire for a 6th gear also, but when - not4resaleZ 12:03:06 05/09/18 no doubt, totally with you on that - LJZTT 15:09:41 05/09/18 An interesting note: - not4resaleZ 12:37:08 05/09/18 It wouldnt surprise me if the Euro-NA got - LJZTT 15:12:30 05/09/18 US TT rear end is a 3.69 for all years. (n/m) - Bernie (NoVA) 01:46:27 05/10/18 I understand and agree. It’s just an odd thing to print so - not4resaleZ 06:40:47 05/10/18
Post a Followup	You cannot reply to this message because you are not logged in.