TwinTurbo.NET: Nissan 300ZX forum - The only quality issue I noticed was with the inlet
Subject
The only quality issue I noticed was with the inlet
Posted by
MixManMash
on February 10, 2018 at 9:34 AM
This message has been viewed
423
times.
In Reply To
True
posted by ConVerTT
on February 09, 2018 at 10:13 PM
Message
piping, specifically the pipe that bolts onto the turbocharger compressor inlet.
Follow Ups
CZP 2.5" Piping & Bell 2.5" SMIC w/ Ducts
-
Bigwill837
10:46:13 02/09/18
I don't think they fit very well
-
WhiTTe Z
11:45:01 02/09/18
This. My one car has the CZP piping and the other has the
-
MixManMash
11:55:09 02/09/18
Ugh...
-
Bigwill837
12:32:40 02/09/18
Order their products from another vendor
-
Zsgetyoulaid
12:52:44 02/09/18
Order the Ash piping from a vendor like Specialty-Z... (n/m)
-
Barry (NJ)
12:53:07 02/09/18
I'll hop in too: This is why SZ carries his parts
-
BlackholeZ
13:03:07 02/09/18
That should be the other way around....
-
Dave N
19:27:45 02/13/18
I buy Ash-spec products from SZ. Only way I will/would buy. (n/m)
-
MixManMash
13:21:13 02/09/18
Agreed. I will never send As(s)h money directly again. (n/m)
-
ConVerTT
15:05:01 02/09/18
go via Specialty Z . (n/m)
-
CmyZ
18:31:44 02/11/18
I second Z1 piping not fitting well at all.
-
TK3Z32(Wi)
14:12:03 02/09/18
I'm curious why there aren't more 2.5" piping kits
-
FrozTTy
12:51:23 02/09/18
It's really not that easy
-
BlackholeZ
13:01:56 02/09/18
It's also not that hard (n/m)
-
ConVerTT
15:07:14 02/09/18
Then give it a shot.
-
BlackholeZ
18:57:46 02/09/18
True
-
ConVerTT
22:13:59 02/09/18
The only quality issue I noticed was with the inlet -
MixManMash
09:34:18 02/10/18
Yes - basically weld quality dropped, both there and on the
-
ConVerTT
10:39:25 02/10/18
Yes, I noticed the drop in weld quality as well (n/m)
-
BlackholeZ
16:16:25 02/10/18
nope, bends wont get around tight spots (n/m)
-
LJZTT
13:12:38 02/09/18
You can still buy the Bell intercoolers direct from Bell (n/m)
-
LitlElvis
15:59:11 02/09/18
Re: You can still buy the Bell intercoolers direct from Bell
-
Bad Fish
16:44:12 02/09/18
I believe Ash uses Bell cores IIRC. (n/m)
-
MixManMash
17:18:21 02/09/18
I liked them enough to buy a set. Beautiful welds, quality
-
LitlElvis
15:49:10 02/10/18
I've worked with (installed) all 3.
-
Boosted1
19:26:27 02/09/18
Can't get CZP piping anymore.
-
Woody75 (Denver)
22:31:46 02/09/18
CZP pipes were ovalled for easier fit in certain areas. (n/m)
-
ZXoltan
08:27:43 02/10/18
Ash piping is a good fit... with some work around it :) (n/m)
-
zxnazx(tt)
20:13:23 02/11/18
Post a
Followup
You cannot reply to this message because you are not
logged in
.