TwinTurbo.NET: Nissan 300ZX forum - I second Z1 piping not fitting well at all.
Subject
I second Z1 piping not fitting well at all.
Posted by
TK3Z32(Wi)
on February 09, 2018 at 2:12 PM
This message has been viewed
386
times.
In Reply To
This. My one car has the CZP piping and the other has the
posted by MixManMash
on February 09, 2018 at 11:55 AM
Message
It rubbed on everything it could.
Follow Ups
CZP 2.5" Piping & Bell 2.5" SMIC w/ Ducts
-
Bigwill837
10:46:13 02/09/18
I don't think they fit very well
-
WhiTTe Z
11:45:01 02/09/18
This. My one car has the CZP piping and the other has the
-
MixManMash
11:55:09 02/09/18
Ugh...
-
Bigwill837
12:32:40 02/09/18
Order their products from another vendor
-
Zsgetyoulaid
12:52:44 02/09/18
Order the Ash piping from a vendor like Specialty-Z... (n/m)
-
Barry (NJ)
12:53:07 02/09/18
I'll hop in too: This is why SZ carries his parts
-
BlackholeZ
13:03:07 02/09/18
That should be the other way around....
-
Dave N
19:27:45 02/13/18
I buy Ash-spec products from SZ. Only way I will/would buy. (n/m)
-
MixManMash
13:21:13 02/09/18
Agreed. I will never send As(s)h money directly again. (n/m)
-
ConVerTT
15:05:01 02/09/18
go via Specialty Z . (n/m)
-
CmyZ
18:31:44 02/11/18
I second Z1 piping not fitting well at all. -
TK3Z32(Wi)
14:12:03 02/09/18
I'm curious why there aren't more 2.5" piping kits
-
FrozTTy
12:51:23 02/09/18
It's really not that easy
-
BlackholeZ
13:01:56 02/09/18
It's also not that hard (n/m)
-
ConVerTT
15:07:14 02/09/18
Then give it a shot.
-
BlackholeZ
18:57:46 02/09/18
True
-
ConVerTT
22:13:59 02/09/18
The only quality issue I noticed was with the inlet
-
MixManMash
09:34:18 02/10/18
Yes - basically weld quality dropped, both there and on the
-
ConVerTT
10:39:25 02/10/18
Yes, I noticed the drop in weld quality as well (n/m)
-
BlackholeZ
16:16:25 02/10/18
nope, bends wont get around tight spots (n/m)
-
LJZTT
13:12:38 02/09/18
You can still buy the Bell intercoolers direct from Bell (n/m)
-
LitlElvis
15:59:11 02/09/18
Re: You can still buy the Bell intercoolers direct from Bell
-
Bad Fish
16:44:12 02/09/18
I believe Ash uses Bell cores IIRC. (n/m)
-
MixManMash
17:18:21 02/09/18
I liked them enough to buy a set. Beautiful welds, quality
-
LitlElvis
15:49:10 02/10/18
I've worked with (installed) all 3.
-
Boosted1
19:26:27 02/09/18
Can't get CZP piping anymore.
-
Woody75 (Denver)
22:31:46 02/09/18
CZP pipes were ovalled for easier fit in certain areas. (n/m)
-
ZXoltan
08:27:43 02/10/18
Ash piping is a good fit... with some work around it :) (n/m)
-
zxnazx(tt)
20:13:23 02/11/18
Post a
Followup
You cannot reply to this message because you are not
logged in
.