Subject	I don't think they fit very well
Posted by	WhiTTe Z on February 09, 2018 at 11:45 AM
	This message has been viewed 646 times.
In Reply To	CZP 2.5" Piping & Bell 2.5" SMIC w/ Ducts posted by Bigwill837 on February 09, 2018 at 10:46 AM
Message	Ash are really the only option for decent fitment as far as I know. "Stance: cuz goin fast cost money yo (n/m) - ZiNnYc 08/09/12 18:23:42"
Follow Ups	CZP 2.5" Piping & Bell 2.5" SMIC w/ Ducts - Bigwill837 10:46:13 02/09/18 I don't think they fit very well - WhiTTe Z 11:45:01 02/09/18 This. My one car has the CZP piping and the other has the - MixManMash 11:55:09 02/09/18 Ugh... - Bigwill837 12:32:40 02/09/18 Order their products from another vendor - Zsgetyoulaid 12:52:44 02/09/18 Order the Ash piping from a vendor like Specialty-Z... (n/m) - Barry (NJ) 12:53:07 02/09/18 I'll hop in too: This is why SZ carries his parts - BlackholeZ 13:03:07 02/09/18 That should be the other way around.... - Dave N 19:27:45 02/13/18 I buy Ash-spec products from SZ. Only way I will/would buy. (n/m) - MixManMash 13:21:13 02/09/18 Agreed. I will never send As(s)h money directly again. (n/m) - ConVerTT 15:05:01 02/09/18 go via Specialty Z . (n/m) - CmyZ 18:31:44 02/11/18 I second Z1 piping not fitting well at all. - TK3Z32(Wi) 14:12:03 02/09/18 I'm curious why there aren't more 2.5" piping kits - FrozTTy 12:51:23 02/09/18 It's really not that easy - BlackholeZ 13:01:56 02/09/18 It's also not that hard (n/m) - ConVerTT 15:07:14 02/09/18 Then give it a shot. - BlackholeZ 18:57:46 02/09/18 True - ConVerTT 22:13:59 02/09/18 The only quality issue I noticed was with the inlet - MixManMash 09:34:18 02/10/18 Yes - basically weld quality dropped, both there and on the - ConVerTT 10:39:25 02/10/18 Yes, I noticed the drop in weld quality as well (n/m) - BlackholeZ 16:16:25 02/10/18 nope, bends wont get around tight spots (n/m) - LJZTT 13:12:38 02/09/18 You can still buy the Bell intercoolers direct from Bell (n/m) - LitlElvis 15:59:11 02/09/18 Re: You can still buy the Bell intercoolers direct from Bell - Bad Fish 16:44:12 02/09/18 I believe Ash uses Bell cores IIRC. (n/m) - MixManMash 17:18:21 02/09/18 I liked them enough to buy a set. Beautiful welds, quality - LitlElvis 15:49:10 02/10/18 I've worked with (installed) all 3. - Boosted1 19:26:27 02/09/18 Can't get CZP piping anymore. - Woody75 (Denver) 22:31:46 02/09/18 CZP pipes were ovalled for easier fit in certain areas. (n/m) - ZXoltan 08:27:43 02/10/18 Ash piping is a good fit... with some work around it :) (n/m) - zxnazx(tt) 20:13:23 02/11/18
Post a Followup	You cannot reply to this message because you are not logged in.