Subject	So what would you expect from mounting this on a mild build?
Posted by	BlackholeZ on February 02, 2018 at 1:32 PM
	This message has been viewed 424 times.
In Reply To	In the dyno testing there was a small difference in turbo posted by Ash's Z on January 31, 2018 at 09:15 PM
Message	Is this an "extreme builds only" kind of part? From what I've seen, your LPHF turbo manifolds will still benefit a small turbo build, is that the same for the plenum? I am definitely building for response more than peak power. -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	New Intake Manifold sample castings. - Ash's Z 10:33:53 01/31/18 Fantastic! - JMartz 11:47:45 01/31/18 Yes, yes & Yes!!! Part of the groupbuy, can´t wait! (n/m) - YamilZ32 12:40:47 01/31/18 lol, get ready..... (n/m) - LJZTT 12:51:35 01/31/18 Oh this time it's different! (n/m) - ZXRider 12:56:44 01/31/18 Re: Oh this time it's different! - YamilZ32 13:02:38 01/31/18 Here's one example. - MixManMash 13:54:35 01/31/18 Actually, I think you are right. - MixManMash 13:49:56 01/31/18 Calm down guys. What is different is the fact the foundry - Ash's Z 14:16:54 01/31/18 Really? They're on track? - RobZ32 14:56:17 01/31/18 Greg has them in stock. A batch is on the way to CZP too. (n/m) - Ash's Z 15:24:33 01/31/18 I Also have inventory of them here and another large batch - Ash's Z 15:37:28 01/31/18 I dunno, sounds on track to me.... - LJZTT 19:40:34 01/31/18 For what is't worth: Once we had the minimum participants - Ash's Z 22:21:58 01/31/18 again, sounds great - LJZTT 10:55:21 02/01/18 Yes, that has worked much better for everyone. - Ash's Z 01:24:01 02/02/18 there are literally tens of thousands of businesses that - LJZTT 10:38:53 02/02/18 you know as well as i do that we'll have to - slayer fan 11:21:05 02/02/18 alluding to that in my original reply to the excited newbie (n/m) - LJZTT 11:34:51 02/02/18 Is this Ash's sole income/job? - compirate 18:16:24 02/03/18 no clue, but that becomes irrelevant once you solicit and - LJZTT 13:49:32 02/04/18 True, but considering the number of where's waldo posts - compirate 18:03:05 02/04/18 Lol. Some people never learn... (n/m) - MixManMash 19:14:55 02/04/18 Very nice! When do you expect finished products? (n/m) - Madhatter10-6 14:41:13 01/31/18 Sample is on the way to me now. Once inspected, 20 days in - Ash's Z 14:52:37 01/31/18 Looking good Ash. Thank you for staying invested. Will there - SlicktopZ 15:09:56 01/31/18 The TB flange is the same as OEM. ROB's 62mm units fit - Ash's Z 15:38:47 01/31/18 Can you explain to us why we will want to spend.... - MeatMan (604Z) 17:37:59 01/31/18 Lol..pretty sure its like $1400 (n/m) - Stanky (BC) 18:04:41 01/31/18 right...... what was I thinking..... duh. (n/m) - MeatMan (604Z) 18:44:36 01/31/18 51RWHP and 40RTWTQ gained at the mid 500RWHP level. - Ash's Z 18:08:06 01/31/18 I would like to see madhatter's question answered as well. (n/m) - MeatMan (604Z) 18:45:11 01/31/18 Answered. (n/m) - Ash's Z 21:23:01 01/31/18 I understand that you are probably heavily constrained... - NNayak 18:04:55 01/31/18 I hear ya. As you mentioned though, space is at a premium. - Ash's Z 18:06:40 01/31/18 Is this new HP at the cost of mid or low end? - Madhatter10-6 18:35:13 01/31/18 shorter runners should move the power band up. - Aaronw 19:06:53 01/31/18 Of course this is for forced induction so runner length - not4resaleZ 13:50:02 02/02/18 In the dyno testing there was a small difference in turbo - Ash's Z 21:15:01 01/31/18 I'm going to make the argument for smaller than - not4resaleZ 12:23:50 02/02/18 So what would you expect from mounting this on a mild build? - BlackholeZ 13:32:43 02/02/18 I'd buy this... - Bigwill837 16:23:50 02/02/18 I’m sure it’s probably far too late, but it would be nice if - Aaronw 19:09:50 01/31/18 There were 3 reasons for casting these in 3 separate parts. - Ash's Z 22:54:30 01/31/18 I was just thinking it would be nice if they were bolt on - Aaronw 04:13:40 02/01/18 Looks awesome - Polish 01:56:33 02/01/18 Check's in the mail. (n/m) - zmenon 03:05:30 02/01/18 How much does each one weigh? (n/m) - CarolinaZ_TT 06:53:40 02/01/18 compatible with BDE top feeds, right? (n/m) - ZiNnYc 17:55:22 02/01/18 BDE and WinFactory, yes. (n/m) - Ash's Z 01:01:40 02/02/18 I would wait for independent test results even if vendors. - michaell32 (FL) 22:20:32 02/01/18 Agreed. (n/m) - MixManMash 23:58:49 02/01/18 Fair enough.. Despite issues in the past in delivering - Ash's Z 01:05:30 02/02/18 any pics of a prototype bolted to a Z ? (n/m) - The Devils Z 00:26:36 02/02/18 Ash, when is the gauge cluster coming out? (n/m) - Boostjuice 00:52:40 02/02/18 I've been running that in my Z now since May of last year - Ash's Z 01:10:14 02/02/18 Here is an example of the prototype being installed. >>> - Ash's Z 01:06:43 02/02/18 Damn, I have too much *stuff in my engine bay (n/m) - FrozTTy 07:04:04 02/02/18 what happens to the air idle control and other OEM - The Devils Z 08:35:19 02/03/18 Re: New Intake Manifold sample castings. - Bigwill837 16:24:41 02/02/18 2nd... (n/m) - ZUL8R 17:43:26 02/02/18 Where's the balance tube? (n/m) - MixManMash 07:50:52 02/03/18 where do coil packs mount? - EngineerLV 14:07:49 02/04/18 I hope not... (n/m) - MixManMash 17:01:38 02/04/18 He figured out you can shorten the stock coils - BlackholeZ 21:54:51 02/04/18 No thanks. There is no obvious design benefit - sparkie 10:02:26 02/06/18
Post a Followup	You cannot reply to this message because you are not logged in.