Subject	Re: I use stock headbolts and no issues with 815WHP.
Posted by	Kvert on September 12, 2017 at 2:18 PM
	This message has been viewed 467 times.
In Reply To	I use stock headbolts and no issues with 815WHP. posted by MixManMash on September 11, 2017 at 07:20 AM
Message	Dam, I ordered the ARP head stud kit from Z1 back in may. Just checked them and they are the chromoly 8740 version. Either I missed it or they added the ARP2000 kit for $83 more just recently. Still building my engine and I can take the head studs out. My goal is ~400WHP max. Should I keep them in or get a set of OEM? If I do swap them out does this require replacing my fresh head gaskets as well?
Follow Ups	Who's using the ARP Chromoly vs ARP 2000? - Zbullet 22:59:06 09/10/17 I use stock headbolts and no issues with 815WHP. - MixManMash 07:20:57 09/11/17 I was aware of that issue as well... - Zbullet 08:57:34 09/11/17 I bought ARP head studs and ordered the Z1 washers - Red Hawk (CO) 10:48:15 09/11/17 Who did you get the ARP kit from? - Bernie (NoVA) 19:29:45 09/11/17 Z1... ah, looks like I missed the part were the kit says - Red Hawk (CO) 08:26:36 09/13/17 Re: I use stock headbolts and no issues with 815WHP. - Kvert 14:18:15 09/12/17 Any idea if the ones you bought were advertised as ARP2000's (n/m) - Zbullet 14:52:18 09/12/17 are these the Chromoly or the 2000s? - Boostjuice 15:01:53 09/12/17 Re: are these the Chromoly or the 2000s? - Kvert 16:55:09 09/12/17 that's a bummer because kyle built my motor with whatever he - Boostjuice 17:07:10 09/12/17 Re: Any idea if the ones you bought were advertised as ARP2000's - Kvert 15:14:04 09/12/17 OEM. And I would replace the head gasket for peace - MixManMash 06:19:56 09/13/17 Article with some info on ARP head studs - Kvert 19:29:08 09/12/17 Lets set a few things straight - Kyle(Houston) 20:09:24 09/12/17 Thank you. (n/m) - Bernie (NoVA) 22:18:44 09/12/17 I think there is more to the cracked washer than more torque - LitlElvis 12:07:42 09/13/17 That is possible..I still stand by the ARP washers over OEM - Kyle(Houston) 14:33:31 09/13/17 Re: Lets set a few things straight - Scott ZShack Taylor 16:59:57 09/13/17 Re: Re: Lets set a few things straight - Kyle(Houston) 21:29:37 09/13/17 Re: Re: Re: Lets set a few things straight - Scott ZShack Taylor 13:53:12 09/14/17 Re: Re: Re: Re: Lets set a few things straight - Kyle(Houston) 18:16:33 09/14/17 Re: Re: Re: Re: Re: Lets set a few things straight - Scott ZShack Taylor 16:02:53 09/15/17 One last time - Kyle(Houston) 22:47:16 09/15/17 ARP 8740 vs ARP2000 vs stock... the truth vs the hype - LitlElvis 20:44:06 09/12/17 Great info. Thanks. (n/m) - Kyle(Houston) 21:15:46 09/12/17 Thank you. (n/m) - Bernie (NoVA) 22:20:45 09/12/17 Thank you, what's recommended torque for L19 's? (n/m) - JaffaUK 07:55:13 09/13/17 Question regarding the preload - ZXRider 12:50:50 09/15/17 Lots of great info! Many thanks for taking the time - Zbullet 23:00:41 09/12/17 Very informative. These discussions are what makes this site - Mike TDK (NoVA) 17:13:46 09/14/17
Post a Followup	You cannot reply to this message because you are not logged in.