TwinTurbo.NET: Nissan 300ZX forum - ouch (n/m)
Subject
ouch (n/m)
Posted by
Madhatter10-6
on July 25, 2017 at 8:11 AM
This message has been viewed
195
times.
In Reply To
Run 600ft-lbs on e85/stock rods they said..it'll be fun..
posted by Stanky (BC)
on July 24, 2017 at 05:24 PM
Message
Follow Ups
Run 600ft-lbs on e85/stock rods they said..it'll be fun..
-
Stanky (BC)
17:24:15 07/24/17
Wow... Back to the drawingboard. (n/m)
-
kickerzx
17:40:33 07/24/17
Uh oh! I sense forged internals in your near future. (n/m)
-
dfenton2
17:58:48 07/24/17
You'll need a few cans of brake clean and rags just
-
MixManMash
18:07:27 07/24/17
I suspect that the amount of torque at low RPMs that you
-
MixManMash
18:21:02 07/24/17
All the oil and coolant is on the highway lol
-
Stanky (BC)
19:09:09 07/24/17
will make an awesome engine block table, DO IT!!
-
LJZTT
16:20:25 07/26/17
It's actually what I plan on doing haha will post pics
-
Stanky (BC)
16:27:16 07/26/17
gonna be sweet, especially if you have some "Alien" -type
-
LJZTT
16:32:35 07/26/17
well you definitely out those shotpeened rods to the test. (n/m)
-
Boostjuice
18:26:37 07/24/17
PDR? (n/m)
-
LJZTT
18:28:07 07/24/17
Heartbreaking
-
Zsgetyoulaid
19:06:39 07/24/17
I knew that corn was gonna get you in trouble...
-
vorpalZ
20:06:53 07/24/17
The corn is a terrible influence..
-
Stanky (BC)
22:25:27 07/24/17
I've got my torque plate all warmed up. lol (n/m)
-
dfenton2
01:10:57 07/25/17
Re: I knew that corn was gonna get you in trouble...
-
ConVerTT
08:28:40 07/25/17
Been there.
-
Boosted1
20:27:47 07/24/17
Re: Run 600ft-lbs on e85/stock rods they said..it'll be fun..
-
Kvert
23:18:02 07/24/17
Once I pull the pan ill have a better idea
-
Stanky (BC)
23:21:55 07/24/17
ouch (n/m) -
Madhatter10-6
08:11:35 07/25/17
well no one can say that you drove her like a princess :-)
-
ConVerTT
08:50:57 07/25/17
Hey, a set of used con bolts and some fiberglass
-
Zorpman
10:08:58 07/25/17
Dont forget the JB Weld and Duct Tape ;-) (n/m)
-
ZXoltan
18:19:35 07/25/17
Did the rod bolts fail? Or the actual rod?
-
ZaXxon
14:16:19 07/25/17
That's what it looks like, but it's hard to say.
-
Stanky (BC)
20:35:26 07/25/17
That looks very much like rod bolt failure.
-
Doug71zt(CAN)
06:36:36 07/26/17
FSM has incorrect rod bolt torque in some editions.
-
Doug71zt(CAN)
06:43:06 07/26/17
I have stock rods with ARPs pressed in and big ends resized
-
ZaXxon
07:01:00 07/26/17
Did you have ARP bolts for the rods? (n/m)
-
EZdusit (cali)
23:11:28 07/25/17
Yep, IIRC IPP uses ARP rod hardware on all his engines (n/m)
-
Stanky (BC)
23:37:26 07/25/17
interesting article on are VG head studs.
-
Boostjuice
12:34:05 07/26/17
Post a
Followup
You cannot reply to this message because you are not
logged in
.