Subject	I converted a double oven into a large single.
Posted by	bartz32tt on February 23, 2017 at 9:46 PM
	This message has been viewed 253 times.
In Reply To	Grimm, what's your pc'ing setup looking like? posted by shiers69 on February 22, 2017 at 03:53 PM
Message	Definitely happy with it. But I recommend getting a smaller oven as well (I'm using a small toaster oven) for hardware and small parts when you don't want to wait for the large oven to heat up. I also built a powder spray booth to cut down on the mess. Good luck, it's a rewarding hobby. I've thought about the side-business thing myself but it's rather time consuming to do it right (media-blast every part first). And your business is limited by size of blast cabinet and oven, which quickly rise in cost unless you DIY. ________________Sig Separator________________________ ATTN: Zuberman The above message is not sponsored by my employer. Selling used ACT full-face sprung clutch kit: $300 + shipping ConUS! Chrome "boost" hardpipes and couplers/clamps $100 + shipping Twin Turbo aluminum front calipers: $200 + shipping. Needs paint or will paint red for additional $50 Parting out my entire 1990 twin turbo! Please email me for needed parts! See profile for my WTB/WTT list as well.
Follow Ups	First attempt to powder coat wheels - timz 15:33:23 02/21/17 Nice job - WhiTTe Z 15:36:15 02/21/17 Re: Nice job - timz 15:39:59 02/21/17 Hope to looks like this when done - timz 15:45:01 02/21/17 Be careful with the torque specs on the used bolts - WhiTTe Z 16:34:21 02/21/17 do you remember what the specs are? I've found mixed info - BOOZT_JUNKIE 08:00:02 02/22/17 I thought Work spec is 19lbs. 40lbs is too much. (n/m) - timz 08:23:03 02/22/17 I mean 19 ft-lbs (n/m) - timz 08:26:00 02/22/17 19 lbs/ft with blue loctite (n/m) - WhiTTe Z 08:24:35 02/22/17 thank you, I will be doing the same soon. Yours looks great (n/m) - BOOZT_JUNKIE 11:44:26 02/22/17 I hope tire installation does not damage them. - JMartz 07:49:07 02/22/17 Only a complete amateur/idiot would use an internal clamp - ttsmokin 09:58:44 02/22/17 This. (n/m) - MixManMash 13:13:43 02/22/17 The manual spoon to break the bead is another lethal - JMartz 17:33:46 02/22/17 Newer machines have a pneumatic lever that never touches - ttsmokin 00:08:18 02/24/17 Yeah who the hell still uses spoons to pop a bead? (n/m) - BlackholeZ 13:33:47 02/25/17 Very nice - shiers69 23:30:17 02/21/17 Re: Very nice - timz 08:21:12 02/22/17 Nice job! - aldian7 00:24:21 02/23/17 You and me both... (n/m) - -Grimm- 10:51:48 02/22/17 Grimm, what's your pc'ing setup looking like? - shiers69 15:53:57 02/22/17 I was just doing it for personal projects - -Grimm- 13:36:06 02/23/17 I converted a double oven into a large single. - bartz32tt 21:46:33 02/23/17 I hope to outsource the media blasting (n/m) - shiers69 18:05:53 02/24/17 Beautiful! (n/m) - JMartz 07:37:46 02/22/17 That looks great! (n/m) - Musashi Sword 09:45:20 02/22/17 Very nice. I approve. (n/m) - Aqualung 09:48:24 02/22/17 Looks great - RobZ32 11:10:37 02/22/17 Looks great Chin! - The Hawk 11:07:18 02/25/17
Post a Followup	You cannot reply to this message because you are not logged in.