Subject	Re: New Single intake plenum design.....without the runners?
Posted by	BarryGZX on December 08, 2016 at 7:07 AM
	This message has been viewed 544 times.
In Reply To	New Single intake plenum design posted by Alan(MD/NJ) on December 07, 2016 at 07:20 PM
Message	There goes the low end torque
Follow Ups	New Single intake plenum design - Alan(MD/NJ) 19:20:51 12/07/16 Yikes... - Stanky 19:37:48 12/07/16 Efan is needed to run this setup - Alan(MD/NJ) 19:41:25 12/07/16 To fund said testing.... (n/m) - MixManMash 23:37:25 12/07/16 Just another machinist that thinks he knows plenum design. - BlackholeZ 20:58:31 12/07/16 Re: Just another machinist that thinks he knows plenum design. - Alan(MD/NJ) 21:14:12 12/07/16 ..... (n/m) - Dane (Houston) 15:18:59 12/08/16 Why would you make that out of billet aluminum? - ZXRider 21:00:50 12/07/16 No videos. (n/m) - Alan(MD/NJ) 21:15:24 12/07/16 They do say that it fits under the hood. (n/m) - BlackholeZ 23:25:36 12/07/16 Recall Ash having a new concept as well. (n/m) - ttz'in (norcal) 00:44:21 12/08/16 holding out for groupbuy on CF windshields (n/m) - LJZTT 01:21:08 12/08/16 Lol! (n/m) - ForceFedTT (SoCal) 22:24:03 12/08/16 Re: New Single intake plenum design.....without the runners? - BarryGZX 07:07:16 12/08/16 group buy before the first car is even done is sketchy af (n/m) - Antihero 09:50:42 12/08/16 adding this to my ASH manifold order - vorpalZ 10:55:36 12/08/16 They had a thread on 3ZC for top-feed fuel rails awhile back - LitlElvis 11:01:15 12/08/16 Bingo! - white22sky 14:44:41 12/08/16 I think it looks interesting... - Madhatter10-6 09:50:33 12/09/16 First thing I noticed was the similarity of the top feed. (n/m) - ForceFedTT (SoCal) 15:07:29 12/09/16 I was expecting better inside runner design for that $amount (n/m) - zilver96 16:10:50 12/09/16 That's a lot of expense to reinvent 1985. - Bernie (NoVA) 17:15:01 12/08/16 LOL! Thank you! (n/m) - ConVerTT 18:24:31 12/08/16 ding ding ding - Adam (NoVA) 09:23:53 12/09/16 Hahaha! Well said Bernie. (n/m) - MixManMash 12:50:38 12/09/16 That top feed design looks familiar ?? (n/m) - ForceFedTT (SoCal) 22:22:09 12/08/16 I know that my response may appear to be biased as I have - Ash's Z 17:38:38 12/10/16 I kind of had to laugh that he disabled comments. (n/m) - BlackholeZ 01:40:41 12/13/16 Re: New Single intake plenum design - Bigwill837 18:15:30 12/10/16
Post a Followup	You cannot reply to this message because you are not logged in.