Subject	Why would you make that out of billet aluminum?
Posted by	ZXRider on December 07, 2016 at 9:00 PM
	This message has been viewed 369 times.
In Reply To	New Single intake plenum design posted by Alan(MD/NJ) on December 07, 2016 at 07:20 PM
Message	What a waste. Water jet the flanges and machine the mating surfaces, the rest of the manifold can be aluminum sheet welded together. One would think they would have it advertised with the engine complete. Do they show a video of the factory hood closing with that manifold?
Follow Ups	New Single intake plenum design - Alan(MD/NJ) 19:20:51 12/07/16 Yikes... - Stanky 19:37:48 12/07/16 Efan is needed to run this setup - Alan(MD/NJ) 19:41:25 12/07/16 To fund said testing.... (n/m) - MixManMash 23:37:25 12/07/16 Just another machinist that thinks he knows plenum design. - BlackholeZ 20:58:31 12/07/16 Re: Just another machinist that thinks he knows plenum design. - Alan(MD/NJ) 21:14:12 12/07/16 ..... (n/m) - Dane (Houston) 15:18:59 12/08/16 Why would you make that out of billet aluminum? - ZXRider 21:00:50 12/07/16 No videos. (n/m) - Alan(MD/NJ) 21:15:24 12/07/16 They do say that it fits under the hood. (n/m) - BlackholeZ 23:25:36 12/07/16 Recall Ash having a new concept as well. (n/m) - ttz'in (norcal) 00:44:21 12/08/16 holding out for groupbuy on CF windshields (n/m) - LJZTT 01:21:08 12/08/16 Lol! (n/m) - ForceFedTT (SoCal) 22:24:03 12/08/16 Re: New Single intake plenum design.....without the runners? - BarryGZX 07:07:16 12/08/16 group buy before the first car is even done is sketchy af (n/m) - Antihero 09:50:42 12/08/16 adding this to my ASH manifold order - vorpalZ 10:55:36 12/08/16 They had a thread on 3ZC for top-feed fuel rails awhile back - LitlElvis 11:01:15 12/08/16 Bingo! - white22sky 14:44:41 12/08/16 I think it looks interesting... - Madhatter10-6 09:50:33 12/09/16 First thing I noticed was the similarity of the top feed. (n/m) - ForceFedTT (SoCal) 15:07:29 12/09/16 I was expecting better inside runner design for that $amount (n/m) - zilver96 16:10:50 12/09/16 That's a lot of expense to reinvent 1985. - Bernie (NoVA) 17:15:01 12/08/16 LOL! Thank you! (n/m) - ConVerTT 18:24:31 12/08/16 ding ding ding - Adam (NoVA) 09:23:53 12/09/16 Hahaha! Well said Bernie. (n/m) - MixManMash 12:50:38 12/09/16 That top feed design looks familiar ?? (n/m) - ForceFedTT (SoCal) 22:22:09 12/08/16 I know that my response may appear to be biased as I have - Ash's Z 17:38:38 12/10/16 I kind of had to laugh that he disabled comments. (n/m) - BlackholeZ 01:40:41 12/13/16 Re: New Single intake plenum design - Bigwill837 18:15:30 12/10/16
Post a Followup	You cannot reply to this message because you are not logged in.